- 您現在的位置：買賣IC網 > Datasheet目錄40 > DS620U+ (Maxim Integrated)IC THERMOMETER/STAT DIG 8MSOP Datasheet資料下載
參數資料
| 型號： | DS620U+ |
| 廠商： | Maxim Integrated |
| 文件頁數： | 7/15頁 |
| 文件大小： | 243K |
| 描述： | IC THERMOMETER/STAT DIG 8MSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±2°C（最小值） |
| 拓撲： | ADC（三角積分型），寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 無 |
| 輸出風扇： | 無 |
| 電源電壓： | 1.7 V ~ 3.5 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 |
| 供應商設備封裝： | 8-uMax-EP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1435 (CN2011-ZH PDF) |
DS620 Digital Thermometer and Thermostat
7 of 15
THERMOSTAT OPERATION
The PO pin on the DS620 operates as the thermostat output when it is configured as PO
-HIGH
or PO
-LOW
through the
P01 and P02 bits of the configuration register. In both of these configurations, PO is updated after every
temperature conversion or write to the temperature register, and remains at the updated value until the next
conversion or write completes. PO
-HIGH
and PO
-LOW
are active-low and are activated and deactivated based on
user-defined upper and lower trip-points. PO
-HIGH
is activated when the measured temperature meets or exceeds
the value stored in the upper trip-point register (T
H
), and stays active until the temperature meets or falls below the
value stored in the lower trip-point register (T
L
) (see Figure 4a). This allows the user to program any amount of
hysteresis into the output response. Similarly, PO
-LOW
is activated when the measured temperature meets or goes
below the value stored in the low trip-point register (T
L
), and stays active until the temperature meets or exceeds
the value stored in the upper trip-point register (T
H
) (see Figure 4b). The T
H
register is located in address spaces
A0h (MSB) and A1h (LSB) and the T
L
register is located in address spaces A2h (MSB) and A3h (LSB) of the
DS620 memory.
The T
H
and T
L
registers (see Table 1) contain centigrade temperature values in twos complement format and are
stored in EEPROM; therefore, they are nonvolatile (NV) and can be programmed prior to installation of the DS620
for use in standalone applications. All bits in the T
H
and T
L
registers are used in the comparison to the temperature
value in the temperature register for the thermostat operation, regardless of the number of bits used for the
temperature conversions as decided by the R0 and R1 bits in the configuration register. Therefore, to ensure
proper thermostat operation, any bits not used for the temperature measurement should be set to 0 in the T
H
and
T
L
registers. For example, for 11-bit temperature conversions, bits 3 and 4 in the T
H
and T
L
register should be set to
0 prior to comparison to the measured temperature. (Bits 0 to 2 are automatically set to 0).
Another thermostat feature is the temperature high and low flags (THF and TLF) in the configuration register.
These bits provide a record of whether the temperature has ever been equal to or greater than T
H
or equal to or
less than T
L
at anytime since power up or since the bits were last cleared. If the temperature ever meets or
exceeds the T
H
register value, the THF bit in the configuration register is set to 1, and if the temperature ever
meets or falls below the T
L
value, the TLF bit in the configuration register is set to 1. Once THF or TLF has been
set, it remains set until the power is cycled or it is overwritten with a 0 by the user.
Figure 4. Thermostat Operation
STANDALONE THERMOSTAT OPERATION
The DS620 can function as a standalone thermostat, i.e., it can provide thermostat functionality without requiring
communication with a microcontroller. For standalone thermostat operation, the T
H
, T
L
, and configuration registers
must be programmed to the desired values prior to installation. For standalone operation, the AUTOC bit in the
configuration register must be set to 1 so that measurements begins automatically at power up. This also
configures the A1 pin as an input pin that can trigger a conversion. In addition, PO must be configured as PO
-HIGH
or PO
-LOW
. The 1SHOT bit in the configuration register is used to enable the DS620 to perform continuous
conversions at power up (1SHOT = 0) or a single conversion (one-shot) at power up or upon request (1SHOT = 1).
In one-shot mode, one conversion is performed at power-up and then the device enters a low-power standby state
until A1 is toggled high. The A1 pin must be toggled low and back high again to start another conversion.
a) PO-high
T
L
T
H
Tem
Lo ic 0
Lo ic 1
T
L
T
H
Lo ic 0
Lo ic 1
Tem
b) PO-low
Temp
Temp
相關PDF資料 |
PDF描述 |
|---|---|
| DS7505U+T&R | IC DGTL THERMOMETER 2WIRE 8-USOP |
| DS75LVU+T&R | IC SENSOR TEMP DIGITAL 8MSOP |
| DS75LXS+ | IC THERMOMETER/STAT DIG 8-SOIC |
| DS75U+T&R | IC THERMOMETER/STAT DIG 8-MSOP |
| FAN4010IL6X_F113 | IC CURRENT SENSE 0.2% 6MLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS620U/T&R | 制造商:Maxim Integrated Products 功能描述:LOW VOLT THERM USOP T&R - Tape and Reel |
| DS620U/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS620U/TR | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Low-Voltage, +-0.5°C Accuracy Digital Thermometer and Thermostat |
| DS620U+ | 功能描述:板上安裝溫度傳感器 Low-Voltage .5+/-C RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS620U+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8MSOP |
發布緊急采購，3分鐘左右您將得到回復。