- 您現在的位置：買賣IC網 > Datasheet目錄40 > HIP6521CB-T (Intersil)IC REG QD BCK/LINEAR SYNC 16SOIC Datasheet資料下載
參數資料
| 型號： | HIP6521CB-T |
| 廠商： | Intersil |
| 文件頁數： | 6/13頁 |
| 文件大小： | 356K |
| 描述： | IC REG QD BCK/LINEAR SYNC 16SOIC |
| 標準包裝： | 2,500 |
| 拓撲： | 降壓（降壓）同步（1），線性（LDO）（3） |
| 功能： | 任何功能 |
| 輸出數： | 4 |
| 頻率 - 開關： | 300kHz |
| 電壓/電流 - 輸出 1： | 控制器 |
| 電壓/電流 - 輸出 2： | 控制器 |
| 電壓/電流 - 輸出 3： | 控制器 |
| 帶 LED 驅動器： | 無 |
| 帶監控器： | 無 |
| 帶序列發生器： | 無 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | * |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | * |
| 包裝： | 帶卷 (TR) |
6
FN4837.5
October 16, 2006
output voltage. As the internal soft-start voltage increases, the
pulse-width on the PHASE pin increases to reach its
steady-state duty cycle at time T2. At time T3, the 3.3V input
supply starts ramping up; as a result, V
OUT2
and V
OUT4
start
ramping up on the second attempt (approximately 3.25 SS
cycles wait), at time T4. During the interval between T4 and T5,
the linear controller error amplifiers references ramp to the final
value bringing all outputs within regulation limits.
Overcurrent Protection
All outputs are protected against excessive overcurrents.
The PWM controller uses the upper MOSFETs
on-resistance, r
DS(ON)
to monitor the current for protection
against shorted output. All linear controllers monitor their
respective FB pins for undervoltage events to protect against
excessive currents.
A sustained overload (undervoltage on linears or overcurrent
on the PWM) on any output results in an independent
shutdown of the respective output, followed by subsequent
individual re-start attempts performed at an interval equivalent
to 3 soft-start intervals. Figure 2 describes the protection
feature. At time T0, an overcurrent event sensed across the
switching regulators upper MOSFET (r
DS(ON)
sensing)
triggers a shutdown of the V
OUT1
output. As a result, its
internal soft-start initiates a number of soft-start cycles. After a
three-cycle wait, the fourth soft-start initiates a ramp-up
attempt of the failed output, at time T2, bringing the output in
regulation at time T4.
To exemplify an UV event on one of the linears, at time T1,
the clock regulator (V
OUT2
) is also subjected to an
overcurrent event, resulting in an UV condition. Similarly,
after three soft-start periods, the fourth cycle initiates a
ramp-up of this linear output at time T3. One soft-start period
after T3, the linear output is within regulation limits. UV
glitches less than 1祍 (typically) in duration are ignored.
As overcurrent protection is performed on the synchronous
switcher regulator on a cycle-by-cycle basis, OC monitoring
is active as long as the regulator is operational. Since the
overcurrent protection on the linear regulators is performed
through undervoltage monitoring at the feedback pins (FB2,
FB3, and FB4), this feature is activated approximately 25%
into the soft-start interval (see Figure 2).
A resistor (R
OCSET
) programs the overcurrent trip level for
the PWM converter. As shown in Figure 3, the internal
40礎 current sink (I
OCSET
) develops a voltage across
R
OCSET
(V
SET
) that is referenced to V
IN
. The DRIVE
signal enables the overcurrent comparator (OCC). When
the voltage across the upper MOSFET (V
DS(ON)
) exceeds
V
SET
, the overcurrent comparator trips to set the
overcurrent latch. Both V
SET
and V
DS(ON)
are referenced
to V
IN
and a small capacitor across R
OCSET
helps
V
OCSET
track the variations of V
IN
due to MOSFET
switching. The overcurrent function will trip at a peak
inductor current (I
PEAK)
determined by:
The OC trip point varies with MOSFETs r
DS(ON)
temperature variations. To avoid overcurrent tripping in the
normal operating load range, determine the R
OCSET
resistor from the equation above with:
FIGURE 1. SOFT-START INTERVAL
0V
0V
TIME
+5V
SB
(0.5V/DIV)
V
OUT2
(2.5V)
V
OUT4
(1.5V)
T1
T2 T3
T0
T4
(1V/DIV)
+3.3V
IN
+5V
DUAL
+3.3V
DUAL
V
OUT3
(1.8V)
V
OUT1
(2.5V)
T5
FIGURE 2. OVERCURRENT/UNDERVOLTAGE PROTECTION
RESPONSE
0V
TIME
(0.5V/DIV.)
V
OUT3
(1.8V)
V
OUT2
(2.5V)
T1
T2
T3
T0
V
OUT4
(1.5V)
V
OUT1
(2.5V)
UV MONITORING
INACTIVE
SOFT-START
FUNCTION
ACTIVE
T4
I
PEAK
=
I
OCSET
R
OCSET
?/DIV>
r
DS ON
( )
--------------------------------------------------- -
HIP6521
相關PDF資料 |
PDF描述 |
|---|---|
| HMC920LP5E | IC CTRLR ACTIVE BIAS 32QFN |
| IDTTSE2002B3CNRG | IC TEMP SENS EEPROM DFN-8 |
| IPM6220ACAZ-T | IC REG 5OUT BUCK/LDO SYNC 24SSOP |
| IR2170 | IC CURRENT SENSE 600V 1MA 8-DIP |
| IR2171STR | IC CURRENT SENSE 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP6521CBZ | 功能描述:電壓模式 PWM 控制器 4 IN 1 PWM/LINEAR CNTRLR 5V RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| HIP6521CBZA | 功能描述:IC REG QD BCK/LINEAR 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| HIP6521CBZA-T | 功能描述:IC REG QD BCK/LINEAR 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| HIP6521CBZ-T | 功能描述:電壓模式 PWM 控制器 4 IN 1 PWM/LINEAR CNTRLR 5V RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| HIP6521EVAL1 | 功能描述:電源管理IC開發工具 HIP6521 PWM & TRPL L LINEAR CNT EVAL BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。