欧美日韩亚洲三区,欧美中文字幕,久久中文在线

參數資料

型號：	IPM6220ACAZ-T
廠商：	Intersil
文件頁數：	7/15頁
文件大小：	527K
描述：	IC REG 5OUT BUCK/LDO SYNC 24SSOP
標準包裝：	2,500
拓撲：	降壓（降壓）同步（3），線性（LDO）（2）
功能：	任何功能
輸出數：	5
頻率 - 開關：	300kHz
電壓/電流 - 輸出 1：	控制器
電壓/電流 - 輸出 2：	控制器
電壓/電流 - 輸出 3：	控制器
帶 LED 驅動器：	無
帶監控器：	無
帶序列發生器：	是
電源電壓：	5.6 V ~ 24 V
工作溫度：	-40°C ~ 85°C
安裝類型：	*
封裝/外殼：	*
供應商設備封裝：	*
包裝：	*

第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁

converters for 5V Main and 3.3V Main buses, two linear

regulators for 3.3V ALWAYS and 5V ALWAYS, and a 12V

boost converter.

The two synchronous converters operate out of phase to

substantially reduce the input-current ripple, minimizing input

filter requirements, minimizing battery heating and

prolonging battery life.

The 12V boost controller uses a 100kHz clock derived from

the main clock. This controller uses leading edge modulation

with the maximum duty cycle limited to 33%.

The chip has three input control lines SDWN1

, SDWN2

and

SDWNALL

. These are provided for Advanced Configuration

and Power Interface (ACPI) compatibility. They turn on and

off all outputs, as well as provide independent control of the

3.3V Main and +5V Main outputs.

To maximize efficiency for the 5V Main and 3.3V Main outputs,

the current-sense technique is based on the lower MOSFET

DS(ON).

Light-load efficiency is further enhanced by a

hysteretic mode of operation which is automatically engaged at

light loads when the inductor current becomes discontinuous.

3.3V Main and 5V Main Architecture

These main outputs are generated from the unregulated

battery input by two independent synchronous buck

converters. The IC integrates all the components required

for output voltage setpoint and feedback compensation,

significantly reducing the number of external components,

saving board space and parts cost.

The buck PWM controllers employ a 300kHz fixed frequency

current-mode control scheme with input voltage feed-

forward ramp programming for better rejection of input

voltage variations.

Figure 4 shows the out-of-phase operation for the 3.3V Main

and 5V Main outputs. The phase node is the junction of the

upper MOSFET, lower MOSFET and the output inductor.

The phase node is high when the upper MOSFET is

conducting and the inductor current rises accordingly. When

the phase node is low, the lower MOSFET is conducting and

the inductor current is ramping down as shown.

Current Sensing and Current Limit Protection

Both PWM converters use the lower MOSFET on-state

resistance, r

DS(ON)

, as the current-sensing element. This

technique eliminates the need for a current sense resistor

and the associated power losses. If more accurate current

protection is desired, current sense resistors may be used in

series with the lower MOSFETs source.

To set the current limit, place a resistor, RSNS, between the

ISEN inputs and the drain of the lower MOSFET (or optional

current sense resistor). The required value of the RSNS

resistor is determined from the following equation:

where IOCDC is the desired DC overcurrent limit; RCS is

either the r

DS(ON)

of the lower MOSFET, or the value of the

optional current-sense resistor, Vo is the output voltage and L

is the output inductor. Also, the value of RCS should be

specified for the expected maximum operating

temperature.

The sensed voltage, and the resulting current out of the

ISEN pin through RSNS, is used for current feedback and

current limit protection. This is compared with an internal

current limit threshold. When a sampled value of the output

current is determined to be above the current limit

threshold, the PWM drive is terminated and a counter is

initiated. This limits the inductor current build-up and

essentially switches the converter into current-limit mode. If

an overcurrent is detected between 26祍 to 53祍 later, an

overcurrent shutdown is initiated. If during the 26祍 to 53祍

period, an overcurrent is not detected, the counter is reset

and sampling continues as normal.

This current limit scheme has proven to be very robust in

applications like portable computers where fast inductor

current build-up is common due to a large difference

between input and output voltages and a low value of the

inductor.

Light-Load (Hysteretic) Operation

In the light-load (hysteretic) mode the output voltage is

regulated by the hysteretic comparator which regulates the

output voltage by maintaining the output voltage ripple as

shown in Figure 5. In Hysteretic mode, the inductor current

flows only when the output voltage reaches the lower limit of

the hysteretic comparator and turns off at the upper limit.

Hysteretic mode saves converter energy at light loads by

supplying energy only at the time when the output voltage

requires it. This mode conserves energy by reducing the

power dissipation associated with continuous switching.

RSNS

Rcs

135礎

----------------- -

Iocdc

L 2 300kHz

?/DIV>

---------------------------------------- -

?/DIV>

100

0 A, V

5V PHASE (10V/DIV.)

1?/SPAN>s/DIV.

L3.3V

(2A/DIV.)

L5V

(2A/DIV.)

= 10.8V

3.3V PHASE (10V/DIV.)

FIGURE 4. OUT OF PHASE OPERATION

IPM6220A

相關PDF資料	PDF描述
IR2170	IC CURRENT SENSE 600V 1MA 8-DIP
IR2171STR	IC CURRENT SENSE 8SOIC
IR2172S	IC CURRENT SENSE 8SOIC
IR2175STR	IC CURRENT SENSE 0.5% 8SOIC
IR22771STRPBF	IC CURRENT SENSE 16SOIC

相關代理商/技術參數	參數描述
IPM6220CA	制造商:Rochester Electronics LLC 功能描述:MULTI-OUTPUT SYSTEM ELECTRONICS REGULATOR FOR MOBIL PCS - Bulk
IPM6220CB	制造商:未知廠家制造商全稱:未知廠家功能描述:Analog IC
IPM6220EVAL1	制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Advanced Triple PWM Only Mode and Dual Linear Power Controller for Portable Applications
IPM-C112	制造商:JDSU 制造商全稱:JDS Uniphase Corporation 功能描述:Miniature Integrated Power Monitor
IPM-C113	制造商:JDSU 制造商全稱:JDS Uniphase Corporation 功能描述:Miniature Integrated Power Monitor

發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

*型號	*數量	廠商	批號	封裝

添加更多采購

我的聯系方式

久久99亚洲热视_国产精品麻豆一区二区_国产精品美女久久久久久不卡_欧美一区二区三区爱爱

久久99亚洲热视_国产精品麻豆一区二区_国产精品美女久久久久久不卡_欧美一区二区三区爱爱

采購需求

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

我的聯系方式