- 您現在的位置：買賣IC網 > Datasheet目錄40 > ISL6160CB-T (Intersil)IC CTRLR BULK/AUXILIARY 14-SOIC Datasheet資料下載
參數資料
| 型號： | ISL6160CB-T |
| 廠商： | Intersil |
| 文件頁數： | 7/11頁 |
| 文件大小： | 262K |
| 描述： | IC CTRLR BULK/AUXILIARY 14-SOIC |
| 標準包裝： | 2,500 |
| 類型： | 電源管理 |
| 應用： | -48V 分布式電源系統，AdvancedTCA ? 系統，Infiniband |
| 內部開關： | 無 |
| 電流限制： | 1A |
| 電源電壓： | 4.5 V ~ 5.5 V，10 V ~ 14 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOICN |
| 包裝： | 帶卷 (TR) |
7
enabling the accompanying voltage converter. The DC-DC
converter then provides a well regulated output voltage to
the IM circuitry.
Available from Intersil is the ISL6160EVAL2. The
ISL6160EVAL2 is a complete InfiniBand Class I (non isolated)
power topology evaluation platform consisting of the ISL6160
and the HIP6006 single output PWM controller. See Figure 2
for a simplified block diagram of the ISL6160EVAL2 platform.
This evaluation platform allows the Infiniband Module (IM)
power supply designer to evaluate the concept of this design
and apply it to a specific IM power requirement. The evaluation
platform is configured for 5V Vout and 3A Iout capability and
exhibits a 92% total efficiency. See Figures 19 and 20 for
ISL6160EVAL2 turn-on and turn-off waveforms.
Additional information for the ISL6160EVAL2 can be found in
application note AN9959.
Using the ISL6160 beyond IM Applications
-48V, +5V Control Circuit
The ISL6160 can also be used for -48V and +5V telecom power
control. The VB portion of the ISL6160 configured as a low side
switch controller as shown in Figure 3. is capable of controlling
several hundreds of volts, positive or negative and at the same
time provide control and protection for the +5V supply with its
1A integrated current regulating function.
Biased by an external 12V reference in the low side switch
configuration the ISL6160 retains all of its features except for
the DC-DC_EN feature. This is nonfunctional in the low side
configuration as V
ISEN
is always near 0V and will not pull high
to indicate that voltage is good.
When controlling a negative voltage the VB_ON control can
be implemented through an optocoupler for on-off control or
left open for an always on hot pluggable adaptor card
application .
Application Considerations
The manufacturers MOSFET safe operating area (SOA) data
should be consulted, as during the soft start ramp and current
regulation times, the VGS of the external N-Channel MOSFETs
is reduced driving the N-Channel MOSFET switch into the
(linear region) high rDS(ON) state. Thus avoid extended soft
start and time out periods as the external N-Channel
MOSFETs may be damaged or destroyed due to excessive
internal power dissipation. Refer to the MOSFET
manufacturers data sheets for SOA information.
With the high levels of inrush current e.g., highly capacitive
loads and HDD motor start up currents, choosing the ramp up
rate and regulation level of the load current is crucial to provide
both protection and still allow for this inrush current without
latching off. Consider this in addition to the time out delay when
choosing MOSFETs for your design.
Correct physical layout of RSENSE resistor is critical to the
accuracy of sensing the VB current. Ideally trace routing
between the R
SENSE
resistors and the ISL6160 is direct and as
short as possible with zero current in the sense lines. (See
Figure 4.)
FIGURE 2. SIMPLIFIED ISL6160EVAL2 BLOCK DIAGRAM
LCL_POWER_EN
VBX_EN_L
ISL6160
HIP6006
VB CONTROL
VA CONTROL
VB_IN
VA_IN
VAout
Vout
VB_ON
DC-DC_ON
EN
HI GATE
LO_GATE
5
6
8
7
4
3
2
1
9
10
11
12
13
14
FIGURE 3. -48V/+5V APPLICATION CIRCUIT
0V
+
-
LOAD
+5V
LOAD
+
-
+5V
12V
REG
-48V
-48V
ISL6160
CORRECT
O ISEN AND
CURRENT
SENSE RESISTOR
INCORRECT
FIGURE 4. SENSE RESISTOR PCB LAYOUT
R
ISET
ISL6160
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6161CB-T | IC CTRLR PWR DISTRIB DUAL 14SOIC |
| ISL6173DRZA-T | IC CTRLR HOT SWAP DUAL LV 28-QFN |
| ISL6174IRZ | IC CIRC BREAKER DUAL LV 28-QFN |
| ISL61861DCBZ | IC USB PWR CTRLR 3A 8SOIC |
| ISL6402IR | IC REG TRPL BCK/LINEAR 28-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6160CBZA | 功能描述:熱插拔功率分布 W/ANNEAL 14LD N 2 OUTPUT HOTPLUG CNTRL RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| ISL6160CBZA-T | 功能描述:熱插拔功率分布 W/ANNEAL 14LD N 2 OUTPUT HOTPLUG CNTRL RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| ISL6160EVAL2 | 功能描述:EVAL BOARD FOR ISL6160/HIP6006 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6160IB | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:InfiniBand +12V Bulk and +5V Auxiliary Power Controller |
| ISL6160IB-T | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:InfiniBand +12V Bulk and +5V Auxiliary Power Controller |
發布緊急采購，3分鐘左右您將得到回復。