- 您現在的位置：買賣IC網 > PDF目錄367494 > L9313 Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications PDF資料下載
參數資料
| 型號： | L9313 |
| 英文描述： | Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| 中文描述： | 線路接口和線路接入電路全功能SLIC和敲響訓練班- 57應用 |
| 文件頁數： | 5/40頁 |
| 文件大小： | 746K |
| 代理商： | L9313 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Data Sheet
September 2001
Full-Feature SLIC and Ringing Relay for TR-57 Applications
L9313 Line Interface and Line Access Circuit
Agere Systems Inc.
5
Description
(continued)
The switch point is a function of the user-programmed
dc current limit and the magnitude of the auxiliary bat-
tery. Switching from the high-voltage to low-voltage
battery is quiet, without interruption of the dc loop cur-
rent, thus preventing any impulse noise generation at
the switch point. Design equations for the switch point
and a graph showing loop/battery current versus loop
resistance are given in the dc Characteristics in the
Application section of this data sheet.
If the user does not want to provide an auxiliary battery,
the design of the L9313 battery switch allows use of a
power control resistor at the auxiliary battery input. This
scheme will not reduce short-loop, off-hook power dis-
sipation, but it will control power dissipation on the
SLIC by sharing power among the SLIC, power resis-
tor, and dc loop. However, in most cases, without the
auxiliary battery, the power dissipation capabilities of
the 44-pin PLCC package are adequate so that the
power control resistor will not be needed. Design equa-
tions for power control options are given in the dc Char-
acteristics section of this data sheet.
The L9313 has two active transmission ready states,
forward active and reverse active. Both on-hook and
off-hook transmission are provided during the forward
and reverse battery modes. Battery reversal is quiet,
without breaking the ac path. Rate of battery reversal
may be ramped to control switching time via optional
external capacitors
.
Equations relating rate of battery
reversal to these optional external capacitors are given
in the dc Characteristics, Power Control section of this
data sheet.
A low-power scan mode is available to reduce idle
mode on-hook power. This mode is realized by using a
scan clamp circuit. In low-power scan mode:
I
The scan clamp circuitry is active.
I
Loop closure is active.
I
All ac transmission, dc feed, and other supervision
circuits, including ring trip, are shut down.
I
Thermal shutdown is active.
I
Low battery sense shutdown is on.
I
On-hook transmission is disabled.
A forward disconnect mode, where all circuits are
turned off and power is denied to the loop, is also pro-
vided. During this mode, the NSTAT supervision output
will read on hook.
In the ring mode, the line break switches are opened
and the power ring access switches are closed. In this
mode, the ring trip detector in the SLIC is active and all
other detectors and the tip/ring drive amplifiers are
turned off to conserve power.
Make-before-break or break-before-make switching is
achievable during ring cadence or ring trip. Toggling
directly into or directly out of the ring mode table will
give make-before-break switching. To achieve break-
before-make switching, go to an intermediate all-off
state (use forward disconnect state) before entering the
ring mode or before leaving the ring mode. See the
Switching Behavior section of this data sheet for more
details on switching behavior.
Voltage transients or impulse noise associated with
ring cadence or ring trip are minimized or eliminated
with the L9313, thus possibly eliminating the need for
external zero-cross switching circuitry.
A tip open switch configuration is also available for
ground start applications. A common-mode current
detector is included.
Both the ring trip and loop closure supervision func-
tions are included. Loop closure threshold is set by
applying a voltage source to the LCTH input. The volt-
age source may be an external voltage source or
derived from the SLIC V
REF
output. A programmable
external voltage source may be used to provide soft-
ware control of the loop closure threshold. Design
equations for the loop closure threshold are given in
the Supervision section of this data sheet.
Hysteresis is
included.
The ring trip detector requires only a single-pole filter at
the input. This will minimize the required number of
external components. To help minimize device power
dissipation, the ring trip detector is active only during
the power ring mode.
Ring trip and loop supervision status outputs appear in
a common output pin, NSTAT. NSTAT is an unlatched
supervision output; thus, an interrupt-based control
scheme may be used.
The dc current limit is set in the active modes via an
applied voltage source. The voltage source may be an
external voltage source. The voltage may be derived
via a resistor divider network from the V
REF
SLIC out-
put. A programmable external voltage source may be
used to provide software control of the loop closure
threshold. Design equations for this feature are given in
the dc Characteristics section of this data sheet. Pro-
gramming range is 10 mA to 45 mA.
Overhead is programmable in the active modes via an
applied voltage
source. The voltage source may be an
external voltage source or derived via a resistor divider
network from the V
REF
SLIC output.
相關PDF資料 |
PDF描述 |
|---|---|
| L9350 | Single Peripheral Driver |
| L9355 | Dual Peripheral Driver |
| L9500A | High-Voltage Ringing SLIC for VolP Applications |
| L9653M | Analog IC |
| L9654M | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9324 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Peripheral Driver |
| L9326 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| L-932P3C | 制造商:Kingbright Corporation 功能描述: |
| L-9331 | 制造商:Ideal Industries Inc 功能描述:L-9331 |
| L9332 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Quad intelligent power low side switch |
發布緊急采購，3分鐘左右您將得到回復。