- 您現在的位置：買賣IC網 > PDF目錄367494 > L9500A High-Voltage Ringing SLIC for VolP Applications PDF資料下載
參數資料
| 型號： | L9500A |
| 英文描述： | High-Voltage Ringing SLIC for VolP Applications |
| 中文描述： | 高壓振鈴用戶接口應用的福爾普 |
| 文件頁數： | 10/32頁 |
| 文件大小： | 616K |
| 代理商： | L9500A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Preliminary Data Sheet
September 2001
High-Voltage Ringing SLIC for VoIP Applications
L9500A
10
Agere Systems Inc.
State Definitions
Forward Active
I
Pin PT is positive with respect to PR.
I
V
BAT2
is applied to tip/ring drive amplifiers.
I
Loop closure and common-mode detect are active.
I
Ring trip detector is turned off to conserve power.
I
Overhead is set to nominal 6.0 V for undistorted
transmission of 3.14 dBm into 900
.
Reverse Active
I
Pin PR is positive with respect to PT.
I
V
BAT2
is applied to tip/ring drive amplifiers.
I
Loop closure and common-mode detect are active.
I
Ring trip detector is turned off to conserve power.
I
Overhead is set to nominal 6.0 V for undistorted
transmission of 3.14 dBm into 900
.
Scan
I
Except for loop closure, all circuits (including ring trip
and common-mode detector) are powered down.
I
On-hook transmission is disabled.
I
Pin PT is positive with respect to PR, and V
BAT1
is
applied to tip/ring.
I
The tip to ring on-hook differential voltage will be typ-
ically between –44 V and –51 V with a –70 V primary
battery.
On-Hook Transmission
—
Forward Battery
I
Pin PT is positive with respect to PR.
I
V
BAT1
is applied to tip/ring drive amplifiers.
I
Supervision circuits, loop closure, and common-
mode detect are active.
I
Ring trip detector is turned off to conserve power.
I
On-hook transmission is allowed.
I
The tip-to-ring on-hook differential voltage will be typ-
ically between –41 V and –49 V with a –70 V primary
battery.
On-Hook Transmission
—
Reverse Battery
I
Pin PR is positive with respect to PT.
I
V
BAT1
is applied to tip/ring drive amplifiers.
I
Supervision circuits, loop closure, and common-
mode detect are active.
I
Ring trip detector is turned off to conserve power.
I
On-hook transmission is allowed.
I
The tip-to-ring on-hook differential voltage will be typ-
ically between –41 V and –49 V with a –70 V primary
battery.
Disconnect
I
The tip/ring amplifiers and all supervision are turned
off.
I
The SLIC goes into a high-impedance state.
I
NSTAT is forced high (on-hook).
I
Device will power up in this state.
Ring
I
Power ring signal is applied to tip and ring.
I
Input waveform at RING
IN
is amplified.
I
Ring trip supervision and common-mode current
supervision are active; loop closure is inactive.
I
Overhead voltage is reduced to typically 4 V.
I
Current is limited by saturation current of the amplifi-
ers themselves, typically 100 mA at 125 °C.
Ground Start
I
Tip drive amplifer is turned off.
I
Device presents a high impedance (>100 k
) to pin
PT.
I
Device presents a clamped (<56.5 V) current-limited
battery (V
BAT1
) to PR.
I
Output pin RGDET indicates current flowing in the
ring lead.
Thermal Shutdown
I
Not controlled via truth table inputs.
I
This mode is caused by excessive heating of the
device, such as may be encountered in an extended
power-cross situation. NSTAT output is forced low or
off hook during a thermal shutdown event.
相關PDF資料 |
PDF描述 |
|---|---|
| L9653M | Analog IC |
| L9654M | Analog IC |
| L9700D | Analog IC |
| L9700 | HEX PRECISION LIMITER |
| L9705D | DOUBLE QUAD CONTACT INTERFACE CIRCUIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9503 | 制造商:Leviton Manufacturing Co 功能描述: |
| L9505 | 制造商:Leviton Manufacturing Co 功能描述: |
| L9508 | 制造商:Leviton Manufacturing Co 功能描述: |
| L9509 | 制造商:Leviton Manufacturing Co 功能描述: |
| L-95-10 | 制造商:Hozan Tool Industrial Co Ltd 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。