- 您現在的位置：買賣IC網 > PDF目錄382300 > MC1GU128HACA (SAMSUNG SEMICONDUCTOR CO. LTD.) MultiMediaCard Specification PDF資料下載
參數資料
| 型號： | MC1GU128HACA |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | MultiMediaCard Specification |
| 中文描述： | 多媒體卡規格 |
| 文件頁數： | 38/66頁 |
| 文件大小： | 1422K |
| 代理商： | MC1GU128HACA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
MultiMediaCard
TM
38
ERASE_GROUP_END(CMD36) command and finally it starts the erase process by issuing the
ERASE(CMD38) command. The address field in the erase commands is an Erase Group address in
byte units. The card will all LSB’s below the Erase Group size, effectively rounding the address down to
the Erase Group boundary.
If an erase command is received out of sequence, the card shall set the ERASE_SEQ_ERROR bit in
the status register and reset the whole sequence.
If an out of sequence(neither of the erase commands, except SEND_STATUS) command received, the
card shall set the ERASE_RESET status bit in the status register, reset the erase sequence and
execute the last command.
If the erase range includes write protected blocks, the shall be left intact and only the non-protected
blocks shall be erased. The WP_ERASE_SKIP status bit in the status register shall be set.
As described above for block write, the card will indicate that an erase is in progress by holding DAT
low The actual erase time may be quite long, and the host may issue CMD7 to deselect the card.
4.9.4 Write Protect Management
Card data may be protected against either erase or write. The entire card may be permanently write
protected by the manufacturer or content provider by setting the permanent or temporary write protect
bits in the CSD. Portions of the data may be protected (in units of WP_GRP_SIZE sectors as specified
in the CSD), and the write protection may be changed by the application. The SET_WRITE_PROT
command sets the write protection of the addressed write-protect group, and the CLR_WRITE_PROT
command clears the write protection of the addressed write-protect group. The SEND_WRITE_PROT
command is similar to a single block read command. The card shall send a data block containing 32
write protection bits (representing 32 write protect groups starting at the specified address) followed by
16 CRC bits. The address field in the write protect commands is a group address in byte units. The
card will ignore all LSB’s below the group size.
4.9.5 Card Lock/Unlock Operation
The password protection feature enables the host to lock a card while providing a password, which
later will be used for unlocking the card. The password and its size are kept in a 128-bit PWD and 8-bit
PWD_LEN registers, respectively. These registers are non-volatile so that a power cycle will not erase
them. Locked cards respond to (and execute) all commands in the "basic" command class (class 0)
and “l(fā)ock card” command class. Thus the host is allowed to reset, initialize, select, query for status,
etc., but not to access data on the card. If the password was previously set (the value of PWD_LEN is
not‘0’) will be locked automatically after power on. Similar to the existing CSD and CID register write
commands the lock/unlock command is available in "transfer state" only. This means that it does not
include an address argument and the card has to be selected before using it. The card lock/unlock
command has the structure and bus transaction type of a regular single block write command. The
transferred data block includes all the required information of the command (password setting mode,
PWD itself, card lock/unlock etc.). The following table describes the structure of the command data
block.
Table 4-9 Card Lock Data Structure
Byte#
Bit7
Bit6
Bit5
0
Reserved
Bit4
Bit3
ERASE
Bit2
LOCK_
UNLOCK
Bit1
CLR_
PWD
Bit0
SET_
PWD
1
2
…
PWD_LEN+1
PWD_LEN
Password data
相關PDF資料 |
PDF描述 |
|---|---|
| MC1DU128HACA | MultiMediaCard Specification |
| MC12U016HACA-0QC00 | MultiMediaCard Specification |
| MC28U032HACA-0QC00 | MultiMediaCard Specification |
| MC12U032HACA-0QC00 | MultiMediaCard Specification |
| MC28U064HACA-0QC00 | MultiMediaCard Specification |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1GU128HACA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU128HACB-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU128HACC-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU128HAFA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU128HAFB-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
發布緊急采購，3分鐘左右您將得到回復。