久久99亚洲热视_国产精品麻豆一区二区_国产精品美女久久久久久不卡_欧美一区二区三区爱爱

您現在的位置：買賣IC網 > PDF目錄382299 > MC2DU016NACA (SAMSUNG SEMICONDUCTOR CO. LTD.) MultiMediaCard Specification PDF資料下載

參數資料

型號：	MC2DU016NACA
廠商：	SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述：	MultiMediaCard Specification
中文描述：	多媒體卡規格
文件頁數：	36/66頁
文件大小：	1422K
代理商：	MC2DU016NACA

MultiMediaCard

Figure 4-3 MultiMediaCard State Diagram

(Data Transfer Mode)

The command SELECT_DESELECT_CARD (CMD7) is used to select one card and place it in the

Transfer State. If a previously selected card is in the Transfer State its connection with the host is

released and it will move back to the Stand-by State. Only one card can be, at any time, in the Transfer

State. A selected card is responding the CMD7, the deselected one does not respond to this command.

When CMD7 is sent including the reserved relative card address “0x0000”, all cards transfer back to

Stand-by State. This command is used to identify new cards without resetting other already acquired

cards. Cards to which an RCA has already been assigned, do not respond to the identification

command flow in this state. All the data communication in the Data Transfer Mode is consequently a

point-to point communication between the host and the selected card (using addressed commands).

All addressed commands are acknowledged by a response on the CMD line. All read commands (data

is sent from the card via data lines) can be interrupted at any time, by a stop command. The data

transfer will terminate and the card will stop or start working on the next command. The DAT bus line

signal level is high when no data is transmitted. A transmitted data block consists of a start bit (LOW),

followed by a continuous data stream.

The data stream contains the net payload data (and error correction bits if an off-card ECC is used).

The data stream ends with an end bit (HIGH). The data transmission is synchronous to the clock signal.

The payload for block-oriented data transfer is preserved by a CRC check sum (refer to Chapter

“Cyclic Redundancy Check (CRC)”).

4.9.1 Block Read

The basic unit of data transfer is a block whose maximum size is defined in the CSD

(READ_BLK_LEN). A CRC is appended to the end of each block ensuring data transfer integrity.

READ_SINGLE_BLOCK (CMD17) starts a block read and after a complete transfer the card goes back

to Transfer State. READ_MULTIPLE_BLOCK (CMD18) starts a transfer of several consecutive blocks.

Two types of multiple block read transactions are defined (the host can use either one at any time):

* Open-ended Multiple block read : The number of blocks for the read multiple block operation is not

相關PDF資料	PDF描述
MC2DU032HACA	MultiMediaCard Specification
MC2DU032NACA	MultiMediaCard Specification
MC2DU064HACA	MultiMediaCard Specification
MC2DU064NACA	MultiMediaCard Specification
MC2DU128HACA	MultiMediaCard Specification

相關代理商/技術參數	參數描述
MC2DU016NACA-0QC00	制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC2DU016NACB-0QC00	制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC2DU016NACC-0QC00	制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC2DU016NAFA-0QC00	制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification
MC2DU016NAFB-0QC00	制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification

發布緊急采購，3分鐘左右您將得到回復。

(若只采購一條型號，填寫一行即可)

*型號	*數量	廠商	批號	封裝

添加更多采購