- 您現在的位置：買賣IC網 > PDF目錄382299 > MC2DU512NACA (SAMSUNG SEMICONDUCTOR CO. LTD.) MultiMediaCard Specification PDF資料下載
參數資料
| 型號： | MC2DU512NACA |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | MultiMediaCard Specification |
| 中文描述： | 多媒體卡規格 |
| 文件頁數： | 31/66頁 |
| 文件大小： | 1422K |
| 代理商： | MC2DU512NACA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
MultiMediaCard
TM
31
Class 0 is mandatory and supported by all cards. It represents the card identification and initialization
commands, which are intended to handle different cards and card types on the same bus lines. The
Card Command Class (CCC) is coded in the card specific data register of each card, so that the host
knows how to access the card. There are four kinds of commands defined on the MultiMediaCard bus:
-
broadcast commands (bc) sent on CMD line, no response.
-
broadcast commands with response (bcr) sent on CMD line, response (all cards simultaneously) on
CMD line
-
addressed (point-to-point) commands (ac) sent on CMD line, response on CMD line.
-
addressed (point-to-point) data transfer commands (adtc) sent on CMD line, response on CMD line,
data transfer on DAT line.
The command transmission always starts with the MSB. Each command starts with a start bit and ends
with a CRC command protection field followed by an end bit. The length of each command frame is
fixed to 48 bits (2.4 us at 20 MHz):
0
1
Bit5 …. Bit0
Bit31 …. Bit0
Start bit
Host
Command
Argument
Bit6 …. Bit0 1
CRC*1
End Bit
The start bit is always ‘0’ in command frames (sent from host to MultiMediaCard). The host bit is
always ‘1’ for commands. The command field contains the binary coded command number. The
argument depends on the command (refer to Table “Basic Commands (class 0) and Table “Block-
Oriented Read Commands (class 2)”). The CRC field is defined in Chapter “Cyclic Redundancy Check
(CRC)”.
The MultiMediaCard supports the following MultiMediaCard commands :
Table 4-8 Detailed Command Description
CMD
Index
Type
Argument
Resp
CMD0
bc
[31:0] stuff bits
CMD1
bcr
[31:0] OCR
without busy
Abbreviation
GO_IDLE_STATE
SEND_OP_COND
Command description
Resets all card to Idle State
Checks for cards not supporting the full
range of 2.0V to 3.6V. After receiving CMD1
the card sends an R3 response (refer to
Chapter “Responses”).
Asks all cards in ready state to send their
CID
*1
numbers
on CMD-line
Assigns relative address to the card in
identification state.
Programs the DSR of all cards in stand-by
state.
These Samsung MultiMediaCard do not
support this command
Command toggles a card between the
standby and transfer states or between the
programming and disconnect state. In both
cases the card is selected by its own
relative address while deselecting the prior
selected card. Address 0 deselects all.
R3
CMD2
bcr
[31:0] stuff bits R2
ALL_SEND_CID
CMD3
ac
[31:16] RCA
[15:0] stuff bits
[31:16] DSR
[15:0] stuff bits
R1
SET_RELATIVE_A
DDR
SET_DSR
CMD4
bc
CMD7
ac
[31:16] RCA
[15:0] stuff bits
R1 (only
the
select
ed
card)
SELECT/
DESELECT_CARD
CMD8
CMD9
reserved
ac
[31:16] RCA
R2
SEND_CSD
Asks the addressed card to send its card-
相關PDF資料 |
PDF描述 |
|---|---|
| MC12U256HACA | MultiMediaCard Specification |
| MC56U064NACA | MultiMediaCard Specification |
| MC1GU064NACA | MultiMediaCard Specification |
| MC56U256HACA | MultiMediaCard Specification |
| MC1GU256HACA | MultiMediaCard Specification |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC2E | 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 1/4-3/4"X1/16" |
| MC2F-1 | 制造商:SPC Multicomp 功能描述:TRANSFORMER VARIABLE 2A 制造商:SPC Multicomp 功能描述:TRANSFORMER, VARIABLE, 2A 制造商:SPC Multicomp 功能描述:TRANSFORMER, VARIABLE, 2A; Input Voltage:240V; Output Current:2A; Knob Rotation:-; AC Power:480VA; Current Rating:2A; External Depth:110mm; External Length / Height:95mm; External Width:110mm; Fixing Centres LxW:92 x 92; Fixing Hole |
| MC2F-1 | 制造商:SPC Multicomp 功能描述:TRANSFORMER VARIABLE 2A |
| MC2GH01GDMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GH256NMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
發布緊急采購，3分鐘左右您將得到回復。