- 您現在的位置：買賣IC網 > PDF目錄382300 > MC2GH01GDMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC2GH01GDMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 16/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC2GH01GDMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
16
Sep.22.2005
Revision 0.3
The MultiMediaCard bus has ten communication lines and three supply lines:
CMD: Command is a bidirectional signal. The host and card drivers are operating in two modes,
open drain and push pull.
DAT0-7: Data lines are bidirectional signals. Host and card drivers are operating in push pull mode
CLK: Clock is a host to card signal. CLK operates in push pull mode
V
DD
: V
DD
is the power supply line for all cards.
V
SS1
, V
SS2
are two ground lines.
Figure 5-1 : Bus Circuitry Diagram
The R
OD
is switched on and off by the host synchronously to the open-drain and push-pull mode transitions. The host
does not have to have open drain drivers, but must recognize this mode to switch on the R
OD
. R
DAT
and R
CMD
are pull-up
resistors protecting the CMD and the DAT lines against bus floating when no card is inserted or when all card drivers are
in a high-impedance mode.
A constant current source can replace the R
OD
by achieving a better performance (constant slopes for the signal rising
and falling edges). If the host does not allow the switchable R
OD
implementation, a fixed R
CMD
can be used (the minimum
value is defined in the Chapter ). Consequently the maximum operating frequency in the open drain mode has to be
reduced if the used R
CMD
value is higher than the minimal one given in Table 5-5.
5.2.1 Hot Insertion and Removal
To guarantee the proper sequence of card pin connection during hot insertion, the use of either a special hot-insertion
capable card connector or an auto-detect loop on the host side (or some similar mechanism) is mandatory (see Chapter 4)
No card shall be damaged by inserting or removing a card into the MultiMediaCard bus even when the power (V
DD
) is up.
Data transfer operations are protected by CRC codes, therefore any bit changes induced by card insertion and removal
can be detected by the MultiMediaCard bus master.
The inserted card must be properly reset also when CLK carries a clock frequency f
PP
. Each card shall have power protec-
tion to prevent card (and host) damage. Data transfer failures induced by removal/insertion are detected by the bus mas-
ter. They must be corrected by the application, which may repeat the issued command.
CMD
CLK
DAT[7:0]
M
H
R
DAT
R
OD
R
CMD
C
1
C
2
C
3
MultiMediaCard
5.2 MultiMediaCard Bus Topology
相關PDF資料 |
PDF描述 |
|---|---|
| MC2GH256NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512DMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH01GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC2GH256NMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GH512DMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GU01GNMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2GU512NMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
發布緊急采購，3分鐘左右您將得到回復。