- 您現在的位置：買賣IC網 > PDF目錄371043 > MC68332AVFC20 (MOTOROLA INC) 32-Bit Modular Microcontroller PDF資料下載
參數資料
| 型號： | MC68332AVFC20 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-Bit Modular Microcontroller |
| 中文描述： | 32-BIT, 20.97 MHz, MICROCONTROLLER, PQFP132 |
| 封裝： | PLASTIC, QFP-132 |
| 文件頁數： | 74/88頁 |
| 文件大小： | 446K |
| 代理商： | MC68332AVFC20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁當前第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
MOTOROLA
74
MC68332
MC68332TS/D
SCK baud rate:
SCK Baud Rate = System Clock/(2SPBR)
or
SPBR = System Clock/(2SCK)(Baud Rate Desired)
where SPBR equals {2, 3, 4,..., 255}
Giving SPBR a value of zero or one disables the baud rate generator. SCK is disabled and assumes its
inactive state value. No serial transfers occur. At reset, baud rate is initialized to one eighth of the sys-
tem clock frequency.
SPCR1 contains parameters for configuring the QSPI before it is enabled. The CPU can read and write
this register, but the QSM has read access only, except for SPE, which is automatically cleared by the
QSPI after completing all serial transfers, or when a mode fault occurs.
SPE — QSPI Enable
0 = QSPI is disabled. QSPI pins can be used for general-purpose I/O.
1 = QSPI is enabled. Pins allocated by PQSPAR are controlled by the QSPI.
DSCKL — Delay before SCK
When the DSCK bit in command RAM is set, this field determines the length of delay from PCS valid to
SCK transition. PCS can be any of the four peripheral chip-select pins. The following equation deter-
mines the actual delay before SCK:
PCS to SCK Delay = [DSCKL/System Clock]
where DSCKL equals {1, 2, 3,..., 127}.
When the DSCK value of a queue entry equals zero, then DSCKL is not used. Instead, the PCS valid-
to-SCK transition is one-half SCK period.
DTL — Length of Delay after Transfer
When the DT bit in command RAM is set, this field determines the length of delay after serial transfer.
The following equation is used to calculate the delay:
Delay after Transfer = [(32DTL)/System Clock]
where DTL equals {1, 2, 3,..., 255}.
A zero value for DTL causes a delay-after-transfer value of 8192/System Clock.
If DT equals zero, a standard delay is inserted.
Standard Delay after Transfer = [17/System Clock]
Delay after transfer can be used to provide a peripheral deselect interval. A delay can also be inserted
between consecutive transfers to allow serial A/D converters to complete conversion.
SPCR1
— QSPI Control Register 1
$YFFC1A
15
14
8
7
0
SPE
DSCKL
DTL
RESET:
0
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| MC68332AVFC16 | 32-Bit Modular Microcontroller |
| MC68332CFC16 | 32-Bit Modular Microcontroller |
| MC68332CFC20 | 32-Bit Modular Microcontroller |
| MC68332MFC16 | 32-Bit Modular Microcontroller |
| MC68332MFC20 | 32-Bit Modular Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68332AVFV16 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332AVFV20 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332CFC16 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332CFC20 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332CFV16 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。