- 您現在的位置：買賣IC網 > PDF目錄371043 > MC68332CFC16 (MOTOROLA INC) 32-Bit Modular Microcontroller PDF資料下載
參數資料
| 型號： | MC68332CFC16 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-Bit Modular Microcontroller |
| 中文描述： | 32-BIT, 16.78 MHz, MICROCONTROLLER, PQFP132 |
| 封裝： | PLASTIC, QFP-132 |
| 文件頁數： | 54/88頁 |
| 文件大小： | 446K |
| 代理商： | MC68332CFC16 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
MOTOROLA
54
MC68332
MC68332TS/D
5.1.7 Period Measurement with Missing Transition Detect (PMM)
Period measurement with missing transition detect allows a special-purpose 23-bit period measure-
ment. It detects the occurrence of a missing transition (caused by a missing tooth on the sensed wheel),
indicated by a period measurement that is greater than a programmable ratio of the previous period
measurement. Once detected, this condition can be counted and compared to a programmable number
of additional transitions detected before TCR2 is reset to $FFFF. In addition, one byte at an address
specified by a channel parameter can be read and used as a flag. A nonzero value of the flag indicates
that TCR2 is to be reset to $FFFF once the next missing transition is detected.
5.1.8 Position-Synchronized Pulse Generator (PSP)
Any channel of the TPU can generate an output transition or pulse, which is a projection in time based
on a reference period previously calculated on another channel. Both TCRs are used in this algorithm:
TCR1 is internally clocked, and TCR2 is clocked by a position indicator in the user's device. An example
of a TCR2 clock source is a sensor that detects special teeth on the flywheel of an automobile using
PMA or PMM. The teeth are placed at known degrees of engine rotation; hence, TCR2 is a coarse rep-
resentation of engine degrees, i.e., each count represents some number of degrees.
Up to 15 position-synchronized pulse generator function channels can operate with a single input ref-
erence channel executing a PMA or PMM input function. The input channel measures and stores the
time period between the flywheel teeth and resets TCR2 when the engine reaches a reference position.
The output channel uses the period calculated by the input channel to project output transitions at spe-
cific engine degrees. Because the flywheel teeth might be 30 or more degrees apart, a fractional multi-
plication operation resolves down to the desired degrees. Two modes of operation allow pulse length
to be determined either by angular position or by time.
5.1.9 Stepper Motor (SM)
The stepper motor control algorithm provides for linear acceleration and deceleration control of a step-
per motor with a programmable number of step rates of up to 14. Any group of channels, up to eight,
can be programmed to generate the control logic necessary to drive a stepper motor.
The time period between steps (P) is defined as:
P(r) = K1 – K2
r
where r is the current step rate (1–14), and K1 and K2 are supplied as parameters.
After providing the desired step position in a 16-bit parameter, the CPU issues a step request. Next, the
TPU steps the motor to the desired position through an acceleration/deceleration profile defined by pa-
rameters. The parameter indicating the desired position can be changed by the CPU while the TPU is
stepping the motor. This algorithm changes the control state every time a new step command is re-
ceived.
A 16-bit parameter initialized by the CPU for each channel defines the output state of the associated
pin. The bit pattern written by the CPU defines the method of stepping, such as full stepping or half step-
ping. With each transition, the 16-bit parameter rotates one bit. The period of each transition is defined
by the programmed step rate.
5.1.10 Period/Pulse-Width Accumulator (PPWA)
The period/pulse-width accumulator algorithm accumulates a 16-bit or 24-bit sum of either the period
or the pulse width of an input signal over a programmable number of periods or pulses (from 1 to 255).
After an accumulation period, the algorithm can generate a link to a sequential block of up to eight chan-
nels. The user specifies a starting channel of the block and number of channels within the block. Gen-
eration of links depends on the mode of operation. Any channel can be used to measure an
accumulated number of periods of an input signal. A maximum of 24 bits can be used for the accumu-
相關PDF資料 |
PDF描述 |
|---|---|
| MC68332CFC20 | 32-Bit Modular Microcontroller |
| MC68332MFC16 | 32-Bit Modular Microcontroller |
| MC68332MFC20 | 32-Bit Modular Microcontroller |
| MC68332TS | 32-Bit Modular Microcontroller |
| MC68332GCFC16 | 32-Bit Modular Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68332CFC20 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332CFV16 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332CFV20 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:32-Bit Modular Microcontroller |
| MC68332GCAG16 | 功能描述:32位微控制器 - MCU 32B MCU 2KRAM TPU QSM RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT |
| MC68332GCAG20 | 功能描述:32位微控制器 - MCU 32B MCU 2KRAM TPU QSM RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。