- 您現在的位置：買賣IC網 > PDF目錄371050 > MC68HC11K0CFU2 (MOTOROLA INC) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | MC68HC11K0CFU2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | QFP-80 |
| 文件頁數： | 19/80頁 |
| 文件大小： | 420K |
| 代理商： | MC68HC11K0CFU2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
M68HC11 K Series
MC6HC11KTS/D
MOTOROLA
19
6.
Clear the EPROG register to reconfigure the EPROM address and data buses for normal op-
eration.
In EPROM emulation mode (PROG mode), the EPROM/OTPROM is programmed as a stand-alone
EPROM by adapting the MCU footprint to the 27C256-type EPROM and using an appropriate EPROM
programmer. To put the MCU in PROG mode, pull the following pins low: MODA/LIR, MODB/V
STBY
,
RESET, PA[2:0]. Refer to
Figure 6
.
In the third method, the EPROM is programmed by software while in the special test or bootstrap
modes. User-developed software can be uploaded through the SCI, or a ROM resident EPROM pro-
gramming utility can be used. To use the resident utility, bootload a three-byte program consisting of a
single jump instruction to $BF00. $BF00 is the starting address of a resident EPROM programming util-
ity. The utility program sets the X and Y index registers to default values, then receives programming
data from an external host and programs it into EPROM. The value in IX determines programming delay
time. The value in IY is a pointer to the first address in EPROM to be programmed (default = $A000).
When the utility program is ready to receive programming data, it sends the host the $FF character.
Then it waits. When the host sees the $FF character, the EPROM programming data is sent, starting
with the first location in the EPROM array. After the last byte to be programmed is sent and the corre-
sponding verification data is returned, the programming operation is terminated by resetting the MCU.
Although the external 12.25 V programming voltage must be applied to the XIRQ/V
PPE
pin during
EPROM programming, it should be equal to V
DD
before verifying the data that was just programmed. It
should equal V
DD
during normal operation also. The XIRQ/V
PPE
pin has a high voltage detect circuit
that inhibits assertion of the ELAT bit when programming voltage is at low levels.
CAUTION
If the MCU is used in any operating mode while high voltage (12.25 V nominal) is
present on the XIRQ/V
PPE
pin, the IRQ/CE pin must be pulled high to avoid acci-
dental programming or corruption of EPROM contents. After programming an
EPROM location, IRQ pin must also be pulled high before the address and data
are changed to program the next location.
MBE —Multiple-Byte Programming Enable
0 = EPROM array configured for normal programming
1 = Program two bytes with the same data
When multiple-byte programming is enabled, address bit 5 is considered a don't care so that bytes with
address bit 5 = 0 and address bit 5 = 1 both get programmed. MBE can be read in any mode and always
reads zero in normal modes. MBE can only be written in special modes.
Bit 6 —Not implemented
Always reads zero
ELAT —EPROM Latch Control
ELAT can be read any time. ELAT can be written any time except when EPGM = 1, then the write to
ELAT will be disabled. When ELAT = 1, writes to EPROM cause address and data to be latched and
the EPROM cannot be read.
0 = EPROM address and data bus configured for normal reads
1 = EPROM address and data bus configured for programming
EPROG
—
EPROM Programming Control
$002B
Bit 7
6
5
4
3
2
1
Bit 0
MBE
—
ELAT
EXCOL
EXROW
—
—
EPGM
RESET:
0
0
0
0
0
0
0
0
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11K0CFU3 | 8-BIT MICROCONTROLLER |
| MC68HC11K0CFU4 | 8-BIT MICROCONTROLLER |
| MC68HC11K0MFN2 | 8-BIT MICROCONTROLLER |
| MC68HC11K0MFN3 | 8-BIT MICROCONTROLLER |
| MC68HC11K0MFN4 | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11K0CFU3 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11K0CFU4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC11K0CFUE4 | 功能描述:8位微控制器 -MCU 8B MCU W/OUT ROM&EEP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC68HC11K0MFN2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11K0MFN3 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。