- 您現在的位置：買賣IC網 > PDF目錄371050 > MC68HC11K0MFN4 (MOTOROLA INC) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | MC68HC11K0MFN4 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQCC84 |
| 封裝： | PLASTIC, LCC-84 |
| 文件頁數： | 42/80頁 |
| 文件大小： | 420K |
| 代理商： | MC68HC11K0MFN4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
MOTOROLA
42
M68HC11 K Series
MC68HC11KTS/D
6 Parallel Input/Output
M68HC11 K-series MCUs have up to 62 input/output lines, depending on the operating mode. To en-
hance the I/O functions, the data bus of this microcontroller is nonmultiplexed. The following table is a
summary of the configuration and features of each port.
NOTE
Port pin function is mode dependent. Do not confuse pin function with the electrical
state of the pin at reset. Port pins are either driven to a specified logic level or are
configured as high impedance inputs. I/O pins configured as high-impedance in-
puts have port data that is indeterminate. The contents of the corresponding latch-
es are dependent upon the electrical state of the pins during reset. In port
descriptions, an "I" indicates this condition. Port pins that are driven to a known log-
ic level during reset are shown with a value of either one or zero. Some control bits
are unaffected by reset. Reset states for these bits are indicated with a "U".
NOTE
To enable PA3 as fourth input capture, set the I4/O5 bit in the PACTL register. Oth-
erwise, PA3 is configured as a fifth output compare out of reset, with bit I4/O5 being
cleared. If the DDA3 bit is set (configuring PA3 as an output), and IC4 is enabled,
writes to PA3 cause edges on the pin to result in input captures. Writing to TI4/O5
has no effect when the TI4/O5 register is acting as IC4. PA7 drives the pulse ac-
cumulator input but also can be configured for general-purpose I/O or output com-
pare. Note that even when PA7 is configured as an output, the pin still drives the
pulse accumulator input.
DDA[7:0] —Data Direction for Port A
0 = Corresponding pin configured for input
1 = Corresponding pin configured for output
Port
Port A
Port B
Port C
Port D
Port E
Port F
Port G
Port H
Input Pins
—
—
—
—
8
—
—
—
Output Pins
—
—
—
—
—
—
—
—
Bidirectional Pins
8
8
8
6
—
8
8
8
Shared Functions
Timer
High Order Address
Data Bus
SCI and SPI
A/D Converter
Low Order Address
Memory Expansion
PWM, Chip Select
PORTA
—Port A Data
$0000
Bit 7
PA7
I
6
5
4
3
2
1
Bit 0
PA0
I
PA6
I
PA5
I
PA4
I
PA3
I
PA2
I
PA1
I
RESET:
Alt. Pin
Func.:
And/or:
PAI
OC1
OC2
OC1
OC3
OC1
OC4
OC1
IC4/OC5
OC1
IC1
—
IC2
—
IC3
—
DDRA
—Data Direction Register for Port A
$0001
Bit 7
DDA7
0
6
5
4
3
2
1
Bit 0
DDA0
0
DDA6
0
DDA5
0
DDA4
0
DDA3
0
DDA2
0
DDA1
0
RESET:
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11K0VFN2 | 8-BIT MICROCONTROLLER |
| MC68HC11K0VFN3 | 8-BIT MICROCONTROLLER |
| MC68HC11K0VFN4 | 8-BIT MICROCONTROLLER |
| MC68HC11K0VFU2 | 8-BIT MICROCONTROLLER |
| MC68HC11K0VFU3 | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11K0VFN2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-Bit Microcontroller |
| MC68HC11K0VFN3 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Technical Summary 8-Bit Microcontroller |
| MC68HC11K0VFN4 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-Bit Microcontroller |
| MC68HC11K0VFU2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-Bit Microcontroller |
| MC68HC11K0VFU3 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。