- 您現在的位置：買賣IC網 > PDF目錄371104 > MGSF1N02LT1 (ON SEMICONDUCTOR) Power MOSFET 750 mAmps, 20 Volts PDF資料下載
參數資料
| 型號： | MGSF1N02LT1 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 小信號晶體管 |
| 英文描述： | Power MOSFET 750 mAmps, 20 Volts |
| 中文描述： | 750 mA, 20 V, N-CHANNEL, Si, SMALL SIGNAL, MOSFET, TO-236AB |
| 封裝： | MINIATURE, CASE 318-08, TO-236, SOT-23, 3 PIN |
| 文件頁數： | 4/6頁 |
| 文件大小： | 187K |
| 代理商： | MGSF1N02LT1 |
4
Motorola Small–Signal Transistors, FETs and Diodes Device Data
INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
SOT–23
mm
inches
0.037
0.95
0.037
0.95
0.079
2.0
0.035
0.9
0.031
0.8
SOT–23 POWER DISSIPATION
The power dissipation of the SOT–23 is a function of the
drain pad size. This can vary from the minimum pad size for
soldering to a pad size given for maximum power dissipation.
Power dissipation for a surface mount device is determined
by TJ(max), the maximum rated junction temperature of the
die, R
θ
JA, the thermal resistance from the device junction to
ambient, and the operating temperature, TA. Using the
values provided on the data sheet for the SOT–23 package,
PD can be calculated as follows:
PD =
TJ(max) – TA
R
θ
JA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25
°
C, one can
calculate the power dissipation of the device which in this
case is 225 milliwatts.
PD =
150
°
C – 25
°
C
556
°
C/W
= 225 milliwatts
The 556
°
C/W for the SOT–23 package assumes the use
of the recommended footprint on a glass epoxy printed circuit
board to achieve a power dissipation of 225 milliwatts. There
are other alternatives to achieving higher power dissipation
from the SOT–23 package. Another alternative would be to
use a ceramic substrate or an aluminum core board such as
Thermal Clad
. Using a board material such as Thermal
Clad, an aluminum core board, the power dissipation can be
doubled using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
Always preheat the device.
The delta temperature between the preheat and
soldering should be 100
°
C or less.*
When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference shall be a maximum of 10
°
C.
The soldering temperature and time shall not exceed
260
°
C for more than 10 seconds.
When shifting from preheating to soldering, the
maximum temperature gradient shall be 5
°
C or less.
After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
Mechanical stress or shock should not be applied during
cooling.
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
相關PDF資料 |
PDF描述 |
|---|---|
| MGSF1N02LT3 | Power MOSFET 750 mAmps, 20 Volts |
| MGSF1N02EL | N-CHANNEL LOGIC LEVEL ENHANCEMENT-MODE TMOS MOSFET |
| MGSF1N02ELT1 | N-CHANNEL LOGIC LEVEL ENHANCEMENT-MODE TMOS MOSFET |
| MGSF1N02ELT3 | N-CHANNEL LOGIC LEVEL ENHANCEMENT-MODE TMOS MOSFET |
| MGSF1N02LT3 | N-CHANNEL ENHANCEMENT-MODE TMOS MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MGSF1N02LT1 | 制造商:ON Semiconductor 功能描述:MOSFET N SOT-23 |
| MGSF1N02LT1_05 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Power MOSFET 750 mAmps, 20 Volts N-Channel SOT-23 |
| MGSF1N02LT1G | 功能描述:MOSFET NFET SOT23 20V 75mA 90mOhm RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| MGSF1N02LT3 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Power MOSFET 750 mAmps, 20 Volts |
| MGSF1N02LT3G | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Power MOSFET 750 mAmps, 20 Volts N-Channel SOT-23 |
發布緊急采購，3分鐘左右您將得到回復。