- 您現在的位置：買賣IC網 > Datasheet目錄40 > DS18B20+PAR (Maxim Integrated)IC THERM MICROLAN PROG-RES TO-92 Datasheet資料下載
參數資料
| 型號： | DS18B20+PAR |
| 廠商： | Maxim Integrated |
| 文件頁數： | 14/19頁 |
| 文件大小： | 221K |
| 描述： | IC THERM MICROLAN PROG-RES TO-92 |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 500 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 100°C |
| 精確度： | ±2°C（最小值） |
| 拓撲： | 寄存器庫，變簽式暫存器 |
| 輸出類型： | 1-Wire? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 100°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | TO-226-3、TO-92-3 標準主體 |
| 供應商設備封裝： | TO-92-3 |
| 包裝： | 管件 |
| 產品目錄頁面： | 1435 (CN2011-ZH PDF) |
DS18B20-PAR
14 of 19
The DS18B20-PAR samples the 1-Wire bus during a window that lasts from 15 約 to 60 約 after the
master initiates the write time slot. If the bus is high during the sampling window, a 1 is written to the
DS18B20-PAR. If the line is low, a 0 is written to the DS18B20-PAR.
READ/WRITE TIME SLOT TIMING DIAGRAM Figure 13
READ TIME SLOTS
The DS18B20-PAR can only transmit data to the master when the master issues read time slots.
Therefore, the master must generate read time slots immediately after issuing a Read Scratchpad [BEh]
command, so that the DS18B20-PAR can provide the requested data. In addition, the master can generate
read time slots after issuing a Recall E
2
[B8h] command to find out the recall status as explained in the
DS18B20-PAR FUNCTION COMMAND section.
All read time slots must be a minimum of 60 約 in duration with a minimum of a 1 約 recovery time
between slots. A read time slot is initiated by the master device pulling the 1-Wire bus low for a
minimum of 1 約 and then releasing the bus (see Figure 13). After the master initiates the read time slot,
the DS18B20-PAR will begin transmitting a 1 or 0 on bus. The DS18B20-PAR transmits a 1 by leaving
the bus high and transmits a 0 by pulling the bus low. When transmitting a 0, the DS18B20-PAR will
release the bus by the end of the time slot, and the bus will be pulled back to its high idle state by the
pullup resister. Output data from the DS18B20-PAR is valid for 15 約 after the falling edge that initiated
45 ?/SPAN>s
15 ?/SPAN>s
V
PU
GND
1-WIRE BUS
60 ?/SPAN>s < T
X
0 < 120
1 ?/SPAN>s < T
REC
<
DS18B20-PAR samples
MIN TYP MAX
15 ?/SPAN>s
30 s
> 1 s
MASTER WRITE 0 SLOT
MASTER WRITE 1 SLOT
DS18B20-PAR samples
MIN TYP MAX
V
PU
GND
1-WIRE BUS
15 s
MASTER READ 0 SLOT
MASTER READ 1 SLOT
Master samples
Master samples
START
OF SLOT
START
OF SLOT
> 1 s
1 ?/SPAN>s < T
REC
<
15 ?/SPAN>s
15 s
30 ?/SPAN>s
15 s
LINE TYPE LEGEND
Bus master pulling low
DS18B20-PAR pulling low
Resistor pullup
> 1 ?/SPAN>s
相關PDF資料 |
PDF描述 |
|---|---|
| DS18B20Z/T&R | IC THERM MICROLAN PROG-RES 8SOIC |
| DS2740U+T&R | IC CURRENT GAUGE(15BIT) 8UMAX |
| DS28EA00U+T&R | IC THERMOMETER 1-WIRE 8-USOP |
| DS3920T-001+ | IC CURRENT MIRROR 5:1 SOT23-6 |
| DS4560LS-LO+T | IC SWITCH HOT-PLUG 12V 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS18B20-PAR/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS18B20-PAR_07 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire Parasite-Power Digital Thermometer |
| DS18B20-PAR+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN PROG-RES TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Prgmble Resolution 1-Wire Parasite Pwr |
| DS18B20-PAR+T&R | 功能描述:板上安裝溫度傳感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS18B20-SL | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Programmable Resolution 1-Wire Digital Thermometer |
發布緊急采購，3分鐘左右您將得到回復。