- 您現在的位置：買賣IC網 > Datasheet目錄40 > DS18B20+PAR (Maxim Integrated)IC THERM MICROLAN PROG-RES TO-92 Datasheet資料下載
參數資料
| 型號： | DS18B20+PAR |
| 廠商： | Maxim Integrated |
| 文件頁數： | 5/19頁 |
| 文件大小： | 221K |
| 描述： | IC THERM MICROLAN PROG-RES TO-92 |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 500 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 100°C |
| 精確度： | ±2°C（最小值） |
| 拓撲： | 寄存器庫，變簽式暫存器 |
| 輸出類型： | 1-Wire? |
| 輸出警報： | 是 |
| 輸出風扇： | 無 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 100°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | TO-226-3、TO-92-3 標準主體 |
| 供應商設備封裝： | TO-92-3 |
| 包裝： | 管件 |
| 產品目錄頁面： | 1435 (CN2011-ZH PDF) |
DS18B20-PAR
5 of 19
The master device can check the alarm flag status of all DS DS18B20-PARs on the bus by issuing an
Alarm Search [ECh] command. Any DS18B20-PARs with a set alarm flag will respond to the command,
so the master can determine exactly which DS18B20-PARs have experienced an alarm condition. If an
alarm condition exists and the T
H
or T
L
settings have changed, another temperature conversion should be
done to validate the alarm condition.
64-BIT LASERED ROM CODE
Each DS18B20-PAR contains a unique 64bit code (see Figure 5) stored in ROM. The least significant 8
bits of the ROM code contain the DS18B20-PARs 1wire family code: 28h. The next 48 bits contain a
unique serial number. The most significant 8 bits contain a cyclic redundancy check (CRC) byte that is
calculated from the first 56 bits of the ROM code. A detailed explanation of the CRC bits is provided in
the CRC GENERATION section. The 64bit ROM code and associated ROM function control logic
allow the DS18B20-PAR to operate as a 1wire device using the protocol detailed in the 1-WIRE BUS
SYSTEM section of this datasheet.
64-BIT LASERED ROM CODE Figure 5
8-BIT CRC
48-BIT SERIAL NUMBER
8-BIT FAMILY CODE (28h)
MEMORY
The DS18B20-PARs memory is organized as shown in Figure 6. The memory consists of an SRAM
scratchpad with nonvolatile EEPROM storage for the high and low alarm trigger registers (T
H
and T
L
)
and configuration register. Note that if the DS18B20-PAR alarm function is not used, the T
H
and T
L
registers can serve as general-purpose memory. All memory commands are described in detail in the
DS18B20-PAR FUNCTION COMMANDS section.
Byte 0 and byte 1 of the scratchpad contain the LSB and the MSB of the temperature register,
respectively. These bytes are read-only. Bytes 2 and 3 provide access to T
H
and T
L
registers. Byte 4
contains the configuration register data, which is explained in detail in the CONFIGURATION
REGISTER section of this datasheet. Bytes 5, 6 and 7 are reserved for internal use by the device and
cannot be overwritten.
Byte 8 of the scratchpad is read-only and contains the cyclic redundancy check (CRC) code for bytes 0
through 7 of the scratchpad. The DS18B20-PAR generates this CRC using the method described in the
CRC GENERATION section.
Data is written to bytes 2, 3, and 4 of the scratchpad using the Write Scratchpad [4Eh] command, and the
data must be transmitted to the DS18B20-PAR starting with the least significant bit of byte 2. To verify
data integrity, the scratchpad can be read (using the Read Scratchpad [BEh] command) after the data is
written. When reading the scratchpad, data is transferred over the 1-Wire bus starting with the least
significant bit of byte 0. To transfer the T
H
, T
L
and configuration data from the scratchpad to EEPROM,
the master must issue the Copy Scratchpad [48h] command.
Data in the EEPROM registers is retained when the device is powered down; at power-up the EEPROM
data is reloaded into the corresponding scratchpad locations. Data can also be reloaded from EEPROM
to the scratchpad at any time using the Recall E
2
[B8h] command. The master can issue read time slots
(see the 1-WIRE BUS SYSTEM section) following the Recall E
2
command and the DS18B20-PAR will
indicate the status of the recall by transmitting 0 while the recall is in progress and 1 when the recall is
done.
MSB
MSB
LSB
LSB
LSB
MSB
相關PDF資料 |
PDF描述 |
|---|---|
| DS18B20Z/T&R | IC THERM MICROLAN PROG-RES 8SOIC |
| DS2740U+T&R | IC CURRENT GAUGE(15BIT) 8UMAX |
| DS28EA00U+T&R | IC THERMOMETER 1-WIRE 8-USOP |
| DS3920T-001+ | IC CURRENT MIRROR 5:1 SOT23-6 |
| DS4560LS-LO+T | IC SWITCH HOT-PLUG 12V 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS18B20-PAR/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS18B20-PAR_07 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire Parasite-Power Digital Thermometer |
| DS18B20-PAR+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN PROG-RES TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Prgmble Resolution 1-Wire Parasite Pwr |
| DS18B20-PAR+T&R | 功能描述:板上安裝溫度傳感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS18B20-SL | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Programmable Resolution 1-Wire Digital Thermometer |
發布緊急采購，3分鐘左右您將得到回復。