- 您現在的位置：買賣IC網 > PDF目錄382300 > MC1GH256DACA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC1GH256DACA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 38/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC1GH256DACA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
38
Sep.22.2005
Revision 0.3
6. MultiMediaCard Protocol Description
All communication between host and card is controlled by the host (master). The host sends commands of two types:
broadcast and addressed (point-to-point) commands.
Broadcast commands : Broadcast commands are intended for all cards in a MultiMediaCard system
1
. Some of these
commands require a response.
Addressed (point-to-point) commands : The addressed commands are sent to the addressed card and cause a
response from this card.
A general overview of the command flow is shown in Figure 6-1 for the card identification mode and in Figure 6-2 for the
data transfer mode. The commands are listed in the command tables (Table 6-9 - Table 6-17). The dependencies between
current state, received command and following state are listed in Table 6-18. In the following sections, the different card
operation modes are described first. Thereafter, the restrictions for controlling the clock signal are defined. All MultiMedi-
aCard commands together with the corresponding responses, state transitions, error conditions and timings are presented
in the succeeding sections.
Three operation modes are defined for the MultiMediaCard system (hosts and cards):
Card identification mode
The host will be in card identification mode after reset, while it is looking for a card on the bus. The card will be in this
mode after reset, until the SET_RCA command (CMD3) is received.
Interrupt mode
Host and card enter and exit interrupt mode simultaneously. In interrupt mode there is no data transfer. The only mes
sage allowed is an interrupt service request from the card or the host.
Data transfer mode
The card will enter data transfer mode once an RCA is assigned to it. The host will enter data transfer mode after iden
tifying the card on the bus.
The following table shows the dependencies between bus modes, operation modes and card states. Each state in the
MultiMediaCard state diagram (see Figure 6-1 and Figure 6-2) is associated with one bus mode and one operation mode:
1.Broadcast commands are kept for backwards compatibility to previous MultiMediaCard systems, where more than one
card was allowed on the bus.
Card state
Operation mode
Bus mode
Inactive State
Inactive
Open-drain
Idle State
Card identification mode
Ready State
Identification State
Stand-by State
Data transfer mode
Push-pull
Transfer State
Bus-Test State
Sending-data State
Receive-data State
Programming State
Disconnect State
Wait-IRQ State
Interrupt mode
Open-drain
相關PDF資料 |
PDF描述 |
|---|---|
| MC2GH01GDMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH256NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512DMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH01GNMCA-2SA00 | SAMSUNG MultiMediaCard |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC1GU016HACA | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACB-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HACC-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC1GU016HAFA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
發布緊急采購，3分鐘左右您將得到回復。