- 您現在的位置：買賣IC網 > PDF目錄382301 > MC4GH02GNMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC4GH02GNMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 9/102頁 |
| 文件大?。?/td> | 1384K |
| 代理商： | MC4GH02GNMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
9
Sep.22.2005
Revision 0.3
Multiple Block Mode
This mode is similar to the single block mode, but the host can read/write multiple data blocks (all have the same length)
which will be stored or retrived from contiguous memory addresses starting at the address specified in the command.
The operation is terminated with a stop transmission command. Misalignment and block length restrictions apply to multi-
ple blocks as well and are identical to the single block read/write operations. Multiple block read with pre-defined block is
supported.
Every sector is protected with an Error Correction Code (ECC). The ECC is generated (in the memory card) when the
sectors are written and validated when the data is read. IF defects are found, the data is corrected prior to transmission to
the host.
The MultiMediaCard can be considered error free and no additional data protection is needed. However, if an applciation
uses additional, exteranal, ECC protection, the data oragnization is defined in the user writeable section of the CSD regis-
ter.
3.8.6 Data Protection in the Flash Card
The smallest erasable unit in the MultiMediaCard is a erase group. In order to speed up the erase procedure, multiple
erase groups can be erased in the same time. The erase operation is divided into two stages.
Tagging - Selecting the Sectors for Erasing
To facilitate selection, a first command with the starting address is followed by a second command with the final address,
and all erase groups within this range will be selected for erase.
Erasing - Starting the Erase Process
Tagging can address erase groups. An arbitrary selection of erase groups may be erased at one time. Tagging and eras-
ing must follow a strict command sequence (refer to the MultiMediaCard standard sepcification for datails).
3.8.7 Erase
The content of an MultiMediaCard can be marked as an original or a copy using the copy bit in the CSD register. Once
the Copy bit is set (maked as a copy) it cannot be cleared.
The Copy bit of the MultiMediaCard is programmed (during test and formatting on the manufacturing floor) as a copy. The
MultiMediaCard can be purchased with the copy bit set (copy) or cleared, indicating the card is a master.
The One Time Programmable (OTP) characteristic of the Copy bit is implemented in the MultiMediaCard controller firm-
ware and not with a physical OTP cell.
3.8.9 Copy Bit
All the configuration information of the MultiMediaCard is stored in the CSD register. The MSB bytes of the register con-
tain manufacturer data and two least significant bytes contains the host controlled data - the card Copy and write protec-
tion and the user ECC register.
The host can read the CSD register and alter the host controlled data bytes using the SEND_CSD and PROGRAM_CSD
commands.
3.8.10 The CSD Register
3.8.8 Write Protection
Two-card level write-protection options are available: permanent and temporary. Both can be set using the
PROGRAM_CSD command (refer to CSD Programming, Section 6.2.8). The permanent write protect bit, once set, can-
not be clearded. This feature is implemented in the MultiMediaCard /RS-MultiMediaCard controller firmware and not with
a physical OTP cell.
相關PDF資料 |
PDF描述 |
|---|---|
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
| MC26LS30 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC26LS30D | CABLE GLAND, PG29 |
| MC26LS30DR2 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC4M | 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM |
| MC-4-MALE | 制造商:Multi-Contact USA 功能描述: |
| MC4MANUAL | 制造商:Omron Corporation 功能描述: |
| MC-4R128CEE6B | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
| MC-4R128CEE6B-653 | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
發布緊急采購，3分鐘左右您將得到回復。