- 您現在的位置：買賣IC網 > PDF目錄371046 > MC68C912B32CFU8 (MOTOROLA INC) 16-Bit Microcontroller PDF資料下載
參數資料
| 型號： | MC68C912B32CFU8 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-Bit Microcontroller |
| 中文描述： | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | QFP-80 |
| 文件頁數： | 47/128頁 |
| 文件大小： | 748K |
| 代理商： | MC68C912B32CFU8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
MC68HC912B32
MC68HC912B32TS/D
MOTOROLA
47
8 EEPROM
The MC68HC912B32 EEPROM serves as a 768-byte nonvolatile memory which can be used for fre-
quently accessed static data or as fast access program code.
The MC68HC912B32 EEPROM is arranged in a 16-bit configuration. The EEPROM array may be read
as either bytes, aligned words or misaligned words. Access times is one bus cycle for byte and aligned
word access and two bus cycles for misaligned word operations.
Programming is by byte or aligned word. Attempts to program or erase misaligned words will fail. Only
the lower byte will be latched and programmed or erased. Programming and erasing of the user EE-
PROM can be done in all operating modes.
Each EEPROM byte or aligned word must be erased before programming. The EEPROM module sup-
ports byte, aligned word, row (32 bytes) or bulk erase, all using the internal charge pump. Bulk erasure
of odd and even rows is also possible in test modes; the erased state is $FF. The EEPROM module
has hardware interlocks which protect stored data from corruption by accidentally enabling the program/
erase voltage. Programming voltage is derived from the internal V
DD
supply with an internal charge
pump. The EEPROM has a minimum program/erase life of 10,000 cycles over the complete operating
temperature range.
8.1 EEPROM Programmer’s Model
The EEPROM module consists of two separately addressable sections. The first is a four-byte memory
mapped control register block used for control, testing and configuration of the EEPROM array. The
second section is the EEPROM array itself.
At reset, the four-byte register section starts at address $00F0 and the EEPROM array is located from
addresses $0D00 to $0FFF (see
Figure 9
). For information on remapping the register block and EE-
PROM address space, refer to
5 Operating Modes and Resource Mapping
.
Read access to the memory array section can be enabled or disabled by the EEON control bit in the
INITEE register. This feature allows the access of memory mapped resources that have lower priority
than the EEPROM memory array. EEPROM control registers can be accessed and EEPROM locations
may be programmed or erased regardless of the state of EEON.
Using the normal EEPROG control, it is possible to continue program/erase operations during WAIT.
For lowest power consumption during WAIT, stop program/erase by turning off EEPGM.
If the STOP mode is entered during programming or erasing, program/erase voltage will be automati-
cally turned off and the RC clock (if enabled) is stopped. However, the EEPGM control bit will remain
set. When STOP mode is terminated, the program/erase voltage will be automatically turned back on if
EEPGM is set.
At bus frequencies below 1 MHz, the RC clock must be turned on for program/erase.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68CK338 | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| MC68EC060 | 32-Bit Microprocessors.(32位微處理器) |
| MC68EN360RC25V | QUad Integrated Communications Controller Users Manual |
| MC68EN360CFE25 | QUad Integrated Communications Controller Users Manual |
| MC68EN360FE25 | AC 4C 4#12 PIN PLUG 023 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68C912B32FU8 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller |
| MC68CK16Z1 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series |
| MC68CK16Z1CAG16 | 功能描述:16位微控制器 - MCU 16BIT 1KRAM 32KHZ CRYSTAL RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MC68CK16Z1CAG16 | 制造商:Freescale Semiconductor 功能描述:Microcontroller |
| MC68CK16Z1CFC16 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series |
發布緊急采購，3分鐘左右您將得到回復。