- 您現在的位置：買賣IC網 > PDF目錄371046 > MC68C912B32FU8 (MOTOROLA INC) 16-Bit Microcontroller PDF資料下載
參數資料
| 型號： | MC68C912B32FU8 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-Bit Microcontroller |
| 中文描述： | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | QFP-80 |
| 文件頁數： | 12/128頁 |
| 文件大小： | 748K |
| 代理商： | MC68C912B32FU8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁
MOTOROLA
12
MC68HC912B32
MC68HC912B32TS/D
3.3.3 Reset (RESET)
An active low bidirectional control signal, RESET, acts as an input to initialize the MCU to a known start-
up state. It also acts as an open-drain output to indicate that an internal failure has been detected in
either the clock monitor or COP watchdog circuit. The MCU goes into reset asynchronously and comes
out of reset synchronously. This allows the part to reach a proper reset state even if the clocks have
failed, while allowing synchronized operation when starting out of reset.
It is possible to determine whether a reset was caused by an internal source or an external source. An
internal source drives the pin low for 16 cycles; eight cycles later the pin is sampled. If the pin has re-
turned high, either the COP watchdog vector or clock monitor vector will be taken. If the pin is still low,
the external reset is determined to be active and the reset vector is taken. Hold reset low for at least 32
cycles to assure that the reset vector is taken in the event that an internal COP watchdog time-out or
clock monitor fail occurs.
3.3.4 Maskable Interrupt Request (IRQ)
The IRQ input provides a means of applying asynchronous interrupt requests to the MCU. Either falling
edge-sensitive triggering or level-sensitive triggering is program selectable (INTCR register). IRQ is al-
ways configured to level-sensitive triggering at reset. When the MCU is reset the IRQ function is
masked in the condition code register.
This pin is always an input and can always be read. In special modes it can be used to apply external
EEPROM V
PP
in support of EEPROM testing. External V
PP
is not needed for normal EEPROM program
and erase cycles. Because the IRQ pin is also used as an EEPROM programming voltage pin, there is
an internal resistive pull-up on the pin.
3.3.5 Nonmaskable Interrupt (XIRQ)
The XIRQ input provides a means of requesting a nonmaskable interrupt after reset initialization. During
reset, the X bit in the condition code register (CCR) is set and any interrupt is masked until MCU soft-
ware enables it. Because the XIRQ input is level sensitive, it can be connected to a multiple-source
wired-OR network. This pin is always an input and can always be read. There is an active pull-up on
this pin while in reset and immediately out of reset. The pull-up can be turned off by clearing PUPE in
the PUCR register. XIRQ is often used as a power loss detect interrupt.
Whenever XIRQ or IRQ are used with multiple interrupt sources (IRQ must be configured for level-sen-
sitive operation if there is more than one source of IRQ interrupt), each source must drive the interrupt
input with an open-drain type of driver to avoid contention between outputs. There must also be an in-
terlock mechanism at each interrupt source so that the source holds the interrupt line low until the MCU
recognizes and acknowledges the interrupt request. If the interrupt line is held low, the MCU will recog-
nize another interrupt as soon as the interrupt mask bit in the MCU is cleared (normally upon return from
an interrupt).
3.3.6 Mode Select (SMODN, MODA, and MODB)
The state of these pins during reset determine the MCU operating mode. After reset, MODA and MODB
can be configured as instruction queue tracking signals IPIPE0 and IPIPE1. MODA and MODB have
active pulldowns during reset.
The SMODN pin can be used as BKGD or TAGHI after reset.
3.3.7 Single-Wire Background Mode Pin (BKGD)
The BKGD pin receives and transmits serial background debugging commands. A special self-timing
protocol is used. The BKGD pin has an active pull-up when configured as input; BKGD has no pull-up
control. Refer to
16 Development Support
.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68B912B32FU8 | 16-Bit Microcontroller |
| MC68C912B32CFU8 | 16-Bit Microcontroller |
| MC68CK338 | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| MC68EC060 | 32-Bit Microprocessors.(32位微處理器) |
| MC68EN360RC25V | QUad Integrated Communications Controller Users Manual |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68CK16Z1 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series |
| MC68CK16Z1CAG16 | 功能描述:16位微控制器 - MCU 16BIT 1KRAM 32KHZ CRYSTAL RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| MC68CK16Z1CAG16 | 制造商:Freescale Semiconductor 功能描述:Microcontroller |
| MC68CK16Z1CFC16 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:M68HC16Z Series |
| MC68CK16Z1CPV16 | 功能描述:16位微控制器 - MCU 16 Bit 16MHz RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。