- 您現在的位置：買賣IC網 > Datasheet目錄40 > DS2740U+T&R (Maxim Integrated)IC CURRENT GAUGE(15BIT) 8UMAX Datasheet資料下載
參數資料
| 型號： | DS2740U+T&R |
| 廠商： | Maxim Integrated |
| 文件頁數： | 13/16頁 |
| 文件大小： | 304K |
| 描述： | IC CURRENT GAUGE(15BIT) 8UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 3,000 |
| 功能： | 電流計（15 位） |
| 輸入電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 帶卷 (TR) |
DS2740
Table 4. FUNCTION COMMANDS
COMMAND
DESCRIPTION
COMMAND
PROTOCOL
BUS STATE
AFTER COMMAND
PROTOCOL
BUS DATA
Read Data
Reads data from
memory starting at
address XX
69h, XX
Master Rx
Up to 256 bytes
of data
Write Data
Writes data to memory
starting at address XX
6Ch, XX
Master Tx
Up to 256 bytes
of data
1-Wire SIGNALING
The 1-Wire bus requires strict signaling protocols to ensure data integrity. The four protocols used by the
DS2740 are as follows: the initialization sequence (reset pulse followed by presence pulse), write 0, write
1, and read data. All of these types of signaling except the presence pulse are initiated by the bus master.
The initialization sequence required to begin any communication with the DS2740 is shown in Figure 11.
A presence pulse following a reset pulse indicates that the DS2740 is ready to accept a net address
command. The bus master transmits (Tx) a reset pulse for t
RSTL
. The bus master then releases the line and
goes into Receive mode (Rx). The 1-Wire bus line is then pulled high by the pullup resistor. After
detecting the rising edge on the DQ pin, the DS2740 waits for t
PDH
and then transmits the presence pulse
for t
PDL
.
Figure 11. 1-Wire INITIALIZATION SEQUENCE
t
R TL
t
PDL
t
R TH
t
PDH
PACK+
PACK-
LINE TYPE LEGEND:
BOTH BUS MASTER AND
DS2740 ACTIVE LOW
DQ
WRITE-TIME SLOTS
A write-time slot is initiated when the bus master pulls the 1-Wire bus from a logic-high (inactive) level
to a logic-low level. There are two types of write-time slots: write 1 and write 0. All write-time slots must
be t
SLOT
in duration with a 1?/SPAN>s minimum recovery time, t
REC
, between cycles. The DS2740 samples the
1-Wire bus line between 15?/SPAN>s and 60?/SPAN>s (between 2?/SPAN>s and 6?/SPAN>s for overdrive speed) after the line falls. If
the line is high when sampled, a write 1 occurs. If the line is low when sampled, a write 0 occurs (see
Figure 12). For the bus master to generate a write 1 time slot, the bus line must be pulled low and then
released, allowing the line to be pulled high within 15?/SPAN>s (2?/SPAN>s for overdrive speed) after the start of the
write-time slot. For the host to generate a write 0 time slot, the bus line must be pulled low and held low
for the duration of the write-time slot.
13 of 16
相關PDF資料 |
PDF描述 |
|---|---|
| DS28EA00U+T&R | IC THERMOMETER 1-WIRE 8-USOP |
| DS3920T-001+ | IC CURRENT MIRROR 5:1 SOT23-6 |
| DS4560LS-LO+T | IC SWITCH HOT-PLUG 12V 8-SOIC |
| DS600U+T&R | IC SENSOR TEMP 8-USOP |
| DS620U+ | IC THERMOMETER/STAT DIG 8MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2741 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Current Monitor and Accumulator with Integrated Sense Resistor |
| DS2741_09 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Current Monitor and Accumulator with Integrated Sense Resistor |
| DS2741N+ | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS2741N+T | 功能描述:電池管理 Current Monitor & Accumulator RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| DS2745 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Cost I2C Battery Monitor |
發布緊急采購，3分鐘左右您將得到回復。