- 您現在的位置：買賣IC網 > Datasheet目錄40 > DS7505U+T&R (Maxim Integrated)IC DGTL THERMOMETER 2WIRE 8-USOP Datasheet資料下載
參數資料
| 型號： | DS7505U+T&R |
| 廠商： | Maxim Integrated |
| 文件頁數： | 9/14頁 |
| 文件大小： | 197K |
| 描述： | IC DGTL THERMOMETER 2WIRE 8-USOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 3,000 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 125°C |
| 精確度： | ±2°C（最小值） |
| 拓撲： | ADC（三角積分型），比較器，寄存器庫 |
| 輸出類型： | I²C?/SMBus? |
| 輸出警報： | 無 |
| 輸出風扇： | 無 |
| 電源電壓： | 1.7 V ~ 3.7 V |
| 工作溫度： | -55°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 帶卷 (TR) |
Register Pointer
The four DS7505 registers each have a unique 2-bit
pointer designation, which is defined in Table 5. When
reading from or writing to the DS7505, the user must
point the DS7505 to the register that is to be
accessed. When reading from the DS7505, once the
pointer is set, it remains pointed at the same register
until it is changed. For example, if the user desires to
perform consecutive reads from the temperature regis-
ter, then the pointer only has to be set to the tempera-
ture register one time, after which all reads are
automatically from the temperature register until the
pointer value is changed. When writing to the DS7505,
the pointer value must be refreshed each time a write is
performed, even if the same register is being written to
twice in a row.
At power-up, the pointer defaults to the temperature
register location. The temperature register can be read
immediately without resetting the pointer.
Changes to the pointer setting are accomplished as
described in the 2-Wire Serial Data Bus section.
2-Wire Serial Data Bus
The DS7505 communicates over a standard bidirection-
al 2-wire serial data bus that consists of a serial clock
(SCL) signal and serial data (SDA) signal. The DS7505
interfaces to the bus through the SCL input pin and
open-drain SDA I/O pin. All communication is MSB first.
The following terminology is used to describe 2-wire
communication:
Master Device: Microprocessor/microcontroller that
controls the slave devices on the bus. The master
device generates the SCL signal and START and STOP
conditions.
Slave: All devices on the bus other than the master.
The DS7505 always functions as a slave.
Bus Idle or Not Busy: Both SDA and SCL remain high.
SDA is held high by a pullup resistor when the bus is
idle, and SCL must either be forced high by the master
(if the SCL output is push-pull) or pulled high by a
pullup resistor (if the SCL output is open drain).
Transmitter: A device (master or slave) that is sending
data on the bus.
Receiver: A device (master or slave) that is receiving
data from the bus.
START Condition: Signal generated by the master to
indicate the beginning of a data transfer on the bus.
The master generates a START condition by pulling
SDA from high to low while SCL is high (see Figure 6).
A repeated START is sometimes used at the end of a
data transfer (instead of a STOP) to indicate that the
master performs another operation.
STOP Condition: Signal generated by the master to
indicate the end of a data transfer on the bus. The mas-
ter generates a STOP condition by transitioning SDA
from low to high while SCL is high (see Figure 6). After
the STOP is issued, the master releases the bus to its
idle state.
Acknowledge (ACK): When a device (either master or
slave) is acting as a receiver, it must generate an
acknowledge (ACK) on the SDA line after receiving
every byte of data. The receiving device performs an
ACK by pulling the SDA line low for an entire SCL peri-
od (see Figure 6). During the ACK clock cycle, the
transmitting device must release SDA. A variation on
the ACK signal is the not acknowledge (NACK). When
the master device is acting as a receiver, it uses a
NACK instead of an ACK after the last data byte to indi-
cate that it is finished receiving data. The master indi-
cates a NACK by leaving the SDA line high during the
ACK clock cycle.
Digital Thermometer and Thermostat
_______________________________________________________________________________________ 9
Table 3. Resolution Configuration
R1
R0
THERMOMETER
RESOLUTION (BITS)
MAX CONVERSION
TIME (ms)
0
0
9
25
0
1
10
50
1
0
11
100
1
1
12
200
Table 4. Fault Tolerance Configuration
F1
F0
CONSECUTIVE OUT-OF-LIMITS
CONVERSIONS TO TRIGGER O.S.
0
0
1
0
1
2
1
0
4
1
1
6
Table 5. Pointer Definition
REGISTER
P1
P0
Temperature
0
0
Configuration
0
1
T
HYST
1
0
T
OS
1
1
相關PDF資料 |
PDF描述 |
|---|---|
| DS75LVU+T&R | IC SENSOR TEMP DIGITAL 8MSOP |
| DS75LXS+ | IC THERMOMETER/STAT DIG 8-SOIC |
| DS75U+T&R | IC THERMOMETER/STAT DIG 8-MSOP |
| FAN4010IL6X_F113 | IC CURRENT SENSE 0.2% 6MLP |
| FAN5069EMTCX | IC REG DL BCK/LINEAR 16TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS75-08B | 功能描述:整流器 75 Amps 800V RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| DS750PED-3 | 功能描述:線性和開關式電源 12V output 750W Platinum RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
| DS750PED-3-001 | 制造商:Emerson Network Power - Embedded Power 功能描述:12V OUTPUT, 750W 1U X 3.4 X 7.8 PLATINUM WITH REVERSE AIR - Bulk 制造商:ARTESYN EMBEDDED TECHNOLOGIES 功能描述:AC/DC CONVERTER 12V 12V 750W 制造商:Emerson Embedded Power 功能描述:AC/DC CONVERTER 12V 12V 750W 制造商:Emerson Network Power - Embedded Power 功能描述:12V output, 750W 1U x 3.4 x 7.8 Platinum with reverse air |
| DS750PED-3-402 | 制造商:Emerson Network Power - Embedded Power 功能描述:- Bulk |
| DS750PED-3-403 | 制造商:Emerson Network Power - Embedded Power 功能描述:12V OUTPUT, 750W 1U X 3.4 X 7.8 PLATINUM WITH REVERSE AIR - Bulk |
發布緊急采購，3分鐘左右您將得到回復。