- 您現在的位置：買賣IC網 > PDF目錄367494 > L9310 Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device PDF資料下載
參數資料
| 型號： | L9310 |
| 英文描述： | Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device |
| 中文描述： | 線路接口和線路接入電路全功能用戶接口，振鈴繼電器，測試接入設備 |
| 文件頁數： | 16/60頁 |
| 文件大小： | 1053K |
| 代理商： | L9310 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
Data Sheet
July 2001
Full-Feature SLIC, Ringing Relay, and Test Access Device
L9310 Line Interface and Line Access Circuit
16
Agere Systems Inc.
State Definitions
Primary Control Modes
Powerup, Forward Battery
I
Normal talk and battery feed state.
I
Pin PT is positive with respect to pin PR.
I
All ac transmission and dc feed circuits are powered
up.
I
On-hook transmission is enabled.
I
Thermal shutdown is active.
I
Battery window comparator sense shutdown is on.
I
Switch break switches (SW1 and SW2) are closed,
and ring access switches (SW3 and SW4) are open.
I
V
BAT1
is applied to tip and ring during on-hook condi-
tions.
I
Automatic battery switch selects V
BAT1
or V
BAT2
dur-
ing off-hook conditions.
I
All supervision circuits except for ring trip detector
are active.
I
Overhead is set via pin OVH.
I
TESTLEV output is in the high-impedance mode,
and TESTSIG input is off unless this feature is
selected via the secondary control table.
I
PPMOUT is in the high-impedance mode, and
PPMIN input is off unless this feature is selected via
the secondary control table.
I
NSTAT represents the loop closure detector status.
Powerup, Reverse Battery
I
Normal talk and battery feed state.
I
Pin PR is positive with respect to pin PT.
I
All ac transmission and dc feed circuits are powered
up.
I
On-hook transmission is enabled.
I
Thermal shutdown is active.
I
Battery window comparator sense shutdown is on.
I
Switch break switches (SW1 and SW2) are closed,
and ring access switches (SW3 and SW4) are open.
I
V
BAT1
is applied to tip and ring during on-hook condi-
tions.
I
Automatic battery switch selects V
BAT1
or V
BAT2
under
off-hook conditions.
I
All supervision circuits except for ring trip detector
are active.
I
Overhead is set via pin OVH.
I
TESTLEV output is in the high-impedance mode,
and TESTSIG input is off unless this feature is
selected via the secondary control table.
I
PPMOUT is in the high-impedance mode, and
PPMIN input is off unless this feature is selected via
the secondary control table.
I
NSTAT represents the loop closure detector status.
Scan
I
Scan clamp circuitry is active.
I
Loop closure is active.
I
All ac transmission, dc feed, and other supervision
circuits, including ring trip, are shut down.
I
PPM is powered down.
I
Thermal shutdown is active.
I
Battery window comparator sense shutdown is on.
I
On-hook transmission is disabled.
I
Pin PT is positive with respect to PR, and V
BAT1
is
applied to tip/ring.
I
Switch break switches (SW1 and SW2) are closed,
and ring access switches (SW3 and SW4) are open.
I
When the scan clamp circuitry is on, overhead volt-
age is fixed and not controlled by OVH. Also the cur-
rent limit is not the normal current limit set at V
PROG
.
I
NSTAT represents the loop closure detector status.
Ground Start
I
Tip amplifier is on, tip break switch is open.
I
The device presents a high impedance (>100 k
) to
pin PT and a current-limited battery (V
BAT2
) to PR.
I
Common-mode current detector is on.
I
Ring trip detector is off.
I
Output TRGDET indicates current flowing in the ring
lead.
I
This is not a defined state in the primary control
mode table. It is achieved via the powerup and the
ring amp states in the primary control mode table.
相關PDF資料 |
PDF描述 |
|---|---|
| L9311 | Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access |
| L9312 | Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications |
| L9313 | Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| L9350 | Single Peripheral Driver |
| L9355 | Dual Peripheral Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9311 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access |
| L9312 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Forward Battery SLIC and Ringing Relay for TR-57 Applications |
| L9313 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Line Interface and Line Access Circuit Full-Feature SLIC and Ringing for TR-57 Applications |
| L9324 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Peripheral Driver |
| L9326 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。