- 您現在的位置：買賣IC網 > PDF目錄371043 > MC68331CFC20 (MOTOROLA INC) User’s Manual PDF資料下載
參數資料
| 型號： | MC68331CFC20 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | User’s Manual |
| 中文描述： | 32-BIT, 20.97 MHz, MICROCONTROLLER, PQFP132 |
| 封裝： | PLASTIC, QFP-132 |
| 文件頁數： | 156/254頁 |
| 文件大小： | 1354K |
| 代理商： | MC68331CFC20 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁當前第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁
MOTOROLA
6-30
QUEUED SERIAL MODULE
MC68331
USER’S MANUAL
6
The SCI receiver has both short and long idle-line detection capability. Idle-line detec-
tion is always enabled. The idle line type (ILT) bit in SCCR1 determines which type of
detection is used. When an idle line condition is detected, the IDLE flag in SCSR is set.
For short idle-line detection, the receiver bit processor counts contiguous logic one bit-
times whenever they occur. Short detection provides the earliest possible recognition
of an idle line condition, because the stop bit and contiguous logic ones before and
after it are counted. For long idle-line detection, the receiver counts logic ones after
the stop bit is received. Only a complete idle frame causes the IDLE flag to be set.
In some applications, CPU overhead can cause a bit-time of logic level one to occur
between frames. This bit-time does not affect content, but if it occurs after a frame of
ones when short detection is enabled, the receiver flags an idle line.
When the idle line interrupt enable (ILIE) bit in SCCR1 is set, an interrupt request is
generated when the IDLE flag is set. The flag is cleared by reading SCSR and SCDR
in sequence. IDLE is not set again until after at least one frame has been received
(RDRF = 1). This prevents an extended idle interval from causing more than one in-
terrupt.
6.4.3.8 Receiver Wakeup
The receiver wakeup function allows a transmitting device to direct a transmission to
a single receiver or to a group of receivers by sending an address frame at the start of
a message. Hardware activates each receiver in a system under certain conditions.
Resident software must process address information and enable or disable receiver
operation.
A receiver is placed in wakeup mode by setting the receiver wakeup (RWU) bit in
SCCR1. While RWU is set, receiver status flags and interrupts are disabled. Although
the CPU can clear RWU, it is normally cleared by hardware during wakeup.
The WAKE bit in SCCR1 determines which type of wakeup is used. When WAKE = 0,
idle-line wakeup is selected. When WAKE = 1, address-mark wakeup is selected. Both
types require a software-based device addressing and recognition scheme.
Idle-line wakeup allows a receiver to sleep until an idle line is detected. When an idle-
line is detected, the receiver clears RWU and wakes up. The receiver waits for the first
frame of the next transmission. The byte is received normally, transferred to register
RDR, and the RDRF flag is set. If software does not recognize the address, it can set
RWU and put the receiver back to sleep. For idle-line wakeup to work, there must be
a minimum of one frame of idle line between transmissions. There must be no idle time
between frames within a transmission.
Address-mark wakeup uses a special frame format to wake up the receiver. When the
MSB of an address-mark frame is set, that frame contains address information. The
first frame of each transmission must be an address frame. When the MSB of a frame
is set, the receiver clears RWU and wakes up. The byte is received normally, trans-
ferred to register RDR, and the RDRF flag is set. If software does not recognize the
address, it can set RWU and put the receiver back to sleep. Address-mark wakeup al-
相關PDF資料 |
PDF描述 |
|---|---|
| MC68331CPV20 | User’s Manual |
| MC68331MFC16 | User’s Manual |
| MC68331MFC20 | User’s Manual |
| MC68332MFV16 | 32-Bit Modular Microcontroller |
| MC68332 | 32-Bit Modular Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68331CFC20B1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述: |
| MC68331CFC25 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述: |
| MC68331CFC25B1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述: |
| MC68331CFV16 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:User’s Manual |
| MC68331CFV20 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:User’s Manual |
發布緊急采購，3分鐘左右您將得到回復。