- 您現在的位置：買賣IC網 > PDF目錄371046 > MC68B912B32FU8 (MOTOROLA INC) 16-Bit Microcontroller PDF資料下載
參數資料
| 型號： | MC68B912B32FU8 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-Bit Microcontroller |
| 中文描述： | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | QFP-80 |
| 文件頁數： | 123/128頁 |
| 文件大?。?/td> | 748K |
| 代理商： | MC68B912B32FU8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁當前第123頁第124頁第125頁第126頁第127頁第128頁
MC68HC912B32
MC68HC912B32TS/D
MOTOROLA
123
16.3 Breakpoints
Hardware breakpoints are used to debug software on the MC68HC912B32 by comparing actual ad-
dress and data values to predetermined data in setup registers. A successful comparison will place the
CPU in background debug mode (BDM) or initiate a software interrupt (SWI). Breakpoint features de-
signed into the MC68HC912B32 include:
Mode selection for BDM or SWI generation
Program fetch tagging for cycle of execution breakpoint
Second address compare in dual address modes
Range compare by disable of low byte address
Data compare in full feature mode for non-tagged breakpoint
Byte masking for high/low byte data compares
R/W compare for non-tagged compares
Tag inhibit on BDM TRACE
16.3.1 Breakpoint Modes
Three modes of operation determine the type of breakpoint in effect.
Dual address-only breakpoints, each of which will cause a software interrupt (SWI)
Single full-feature breakpoint which will cause the part to enter background debug mode (BDM)
Dual address-only breakpoints, each of which will cause the part to enter BDM
Breakpoints will not occur when BDM is active.
16.3.1.1 SWI Dual Address Mode
In this mode, dual address-only breakpoints can be set, each of which cause a software interrupt. This
is the only breakpoint mode which can force the CPU to execute a SWI. Program fetch tagging is the
default in this mode; data breakpoints are not possible. In the dual mode each address breakpoint is
affected by the BKPM bit and the BKALE bit. The BKxRW and BKxRWE bits are ignored. In dual ad-
dress mode the BKDBE becomes an enable for the second address breakpoint. The BKSZ8 bit will
have no effect when in a dual address mode.
16.3.1.2 BDM Full Breakpoint Mode
A single full feature breakpoint which causes the part to enter background debug mode. BDM mode
may be entered by a breakpoint only if an internal signal from the BDM indicates background debug
mode is enabled.
Breakpoints are not allowed if the BDM mode is already active. Active mode means the CPU is
executing out of the BDM ROM.
BDM should not be entered from a breakpoint unless the ENABLE bit is set in the BDM. This is
important because even if the ENABLE bit in the BDM is negated the CPU actually does execute
the BDM ROM code. It checks the ENABLE and returns if not set. If the BDM is not serviced by
the monitor then the breakpoint would be re-asserted when the BDM returns to normal CPU flow.
There is no hardware to enforce restriction of breakpoint operation if the BDM is not enabled.
16.3.1.3 BDM Dual Address Mode
Dual address-only breakpoints, each of which cause the part to enter background debug mode. In the
dual mode each address breakpoint is affected, consistent across modes, by the BKPM bit, the BKALE
bit, and the BKxRW and BKxRWE bits. In dual address mode the BKDBE becomes an enable for the
second address breakpoint. The BKSZ8 bit will have no effect when in a dual address mode. BDM mode
may be entered by a breakpoint only if an internal signal from the BDM indicates background debug
mode is enabled.
BKDBE will be used as an enable for the second address only breakpoint.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68C912B32CFU8 | 16-Bit Microcontroller |
| MC68CK338 | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| MC68EC060 | 32-Bit Microprocessors.(32位微處理器) |
| MC68EN360RC25V | QUad Integrated Communications Controller Users Manual |
| MC68EN360CFE25 | QUad Integrated Communications Controller Users Manual |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68BOOL | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU) |
| MC68BOOP | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU) |
| MC68BOOS | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-BIT MICROPROCESSING UNIT (MPU) |
| MC68C812A4 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Technical Supplement MC68C812A4 3.3V Electrical Characteristics |
| MC68C912B32CFU8 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:16-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。