- 您現在的位置：買賣IC網 > Datasheet目錄49 > 4432-T-B1 B 915 (Silicon Laboratories Inc)KIT DEV TEST EZRADIOPRO SI4432 Datasheet資料下載
參數資料
| 型號： | 4432-T-B1 B 915 |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 22/47頁 |
| 文件大小： | 799K |
| 描述： | KIT DEV TEST EZRADIOPRO SI4432 |
| 標準包裝： | 1 |
| 附件類型： | 測試卡，收發器，915MHz |
| 適用于相關產品： | EZRadioPRO? |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
Si4430/31/32-B1
22
Rev 1.1
3.2.3. TX State
The TX state may be entered from any of the IDLE modes when the txon bit is set to 1 in "Register 07h. Operating
Mode and Function Control 1". A built-in sequencer takes care of all the actions required to transition between
states from enabling the crystal oscillator to ramping up the PA. The following sequence of events will occur
automatically when going from STANDBY mode to TX mode by setting the txon bit.
1. Enable the main digital LDO and the Analog LDOs.
2. Start up crystal oscillator and wait until ready (controlled byan internal timer).
3. Enable PLL.
4. Calibrate VCO (this action is skipped when the skipvco bit is 1, default value is 0).
5. Wait until PLL settles to required transmit frequency (controlled by an internal timer).
6. Activate power amplifier and wait until power ramping is completed (controlled by an internal timer).
7. Transmit packet.
Steps in this sequence may be eliminated depending on which IDLE mode the chip is configured to prior to setting
the txon bit. By default, the VCO and PLL are calibrated every time the PLL is enabled.
3.2.4. RX State
The RX state may be entered from any of the IDLE modes when the rxon bit is set to 1 in "Register 07h. Operating
Mode and Function Control 1". A built-in sequencer takes care of all the actions required to transition from one of
the IDLE modes to the RX state. The following sequence of events will occur automatically to get the chip into RX
mode when going from STANDBY mode to RX mode by setting the rxon bit:
1. Enable the main digital LDO and the Analog LDOs.
2. Start up crystal oscillator and wait until ready (controlled by an internal timer).
3. Enable PLL.
4. Calibrate VCO (this action is skipped when the skipvco bit is 1, default value is 0).
5. Wait until PLL settles to required receive frequency (controlled by an internal timer).
6. Enable receive circuits: LNA, mixers, and ADC.
7. Enable receive mode in the digital modem.
Depending on the configuration of the radio all or some of the following functions will be performed automatically by
the digital modem: AGC, AFC (optional), update status registers, bit synchronization, packet handling (optional)
including sync word, header check, and CRC.
3.2.5. Device Status
The operational status of the chip can be read from "Register 02h. Device Status".
Add R/W Function/Description
D7
D6
D5
D4
D3
D2
D1
D0 POR Def.
02
R
Device Status
ffovfl ffunfl
rxffem
headerr
freqerr
cps[1] cps[0]
相關PDF資料 |
PDF描述 |
|---|---|
| 5250AT43A200E | ANTENNA CHIP 5.25GHZ WIFI |
| 5250BL14B100T | BALUN CERAMIC CHIP WIFI 5250MHZ |
| 5250BL15B100E | BALUN CERAMIC CHIP WIFI 5250MHZ |
| 5325BL15B050E | BALUN CERAMIC CHIP WIFI 5325MHZ |
| 5512BL15B100E | BALUN CERAMIC CHIP WIFI 5512MHZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 4432-T-B1C470 | 制造商:Silicon Laboratories Inc 功能描述:One antenna Tx/Rx test card 470MHz |
| 4432-T-B1C915 | 制造商:Silicon Laboratories Inc 功能描述:One antenna Tx/Rx test card 915MHz |
| 4432W-1"x72yd | 功能描述:膠帶 70002457219 4432W YDA WHITE 1 IN X 72 YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds |
| 4432W-1/2"x72yd | 功能描述:膠帶 4432WYDA WHITE 1/2X72YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds |
| 4432W-1/2X72YD | 制造商:3M Electronic Products Division 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。