- 您現在的位置：買賣IC網 > PDF目錄382300 > MC2GH256NMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC2GH256NMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 43/102頁 |
| 文件大?。?/td> | 1384K |
| 代理商： | MC2GH256NMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
43
Sep.22.2005
Revision 0.3
All data communication in the Data Transfer Mode is point-to point between the host and the selected card (using
addressed commands). All addressed commands get acknowledged by a response on the CMD line.
The relationship between the various data transfer modes is summarized below (see Figure 6-2):
All data read commands can be aborted any time by the stop command (CMD12). The data transfer will terminate and
the card will return to the
Transfer State.
The read commands are: block read (CMD17), multiple block read (CMD18)
and send write protect (CMD30).
All data write commands can be aborted any time by the stop command (CMD12). The write commands must be
stopped prior to deselecting the card by CMD7. The write commands are: block write (CMD24 and CMD25), write CID
(CMD26), and write CSD (CMD27).
As soon as the data transfer is completed, the card will exit the data write state and move either to the
Programming
State
(transfer is successful) or
Transfer State
(transfer failed).
If a block write operation is stopped and the block length and CRC of the last block are valid, the data will be pro
grammed.
The card may provide buffering for stream and block write. This means that the next block can be sent to the card while
the previous is being programmed.
If all write buffers are full, and as long as the card is in
Programming State
(see MultiMediaCard state diagram
Figure -2), the DAT0 line will be kept low.
There is no buffering option for write CSD, write CID, write protection and erase. This means that while the card is busy
servicing any one of these commands, no other data transfer commands will be accepted. DAT0 line will be kept low as
long as the card is busy and in the
Programming State
.
Parameter set commands are
not
allowed while card is programming.
Parameter set commands are: set block length (CMD16), and erase group selection (CMD35-36).
Read commands are
not
allowed while card is programming.
Moving another card from
Stand-by
to
Transfer State
(using CMD7) will not terminate a programming operation. The
card will switch to the
Disconnect State
and will release the DAT0 line.
A card can be reselected while in the
Disconnect State
, using CMD7. In this case the card will move to the
Program
ming State
and reactivate the busy indication.
Resetting a card (using CMD0 or CMD15) will terminate any pending or active programming operation. This may
destroy the data contents on the card. It is up to the host’s responsibility to prevent this.
Prior to executing the bus testing procedure (CMD19, CMD14), it is recommended to set up the clock frequency used
for data transfer. This way the bus test gives a true result, which might not be the case if the bus testing procedure is
performed with lower clock frequency than the data transfer frequency.
In the following format definitions, all upper case flags and parameters are defined in the CSD (Chapter 5.5.3), and the
other status flags in the Card Status (Chapter 6.9).
相關PDF資料 |
PDF描述 |
|---|---|
| MC2GH512DMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH01GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC2GH512DMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GU01GNMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2GU512NMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2M | 制造商:G & J HALL 功能描述:STEP DRILL 10-20MM 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP; Drill Bit Size Metric:10mm; Overall Length:77.5mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Material:Steel; Material Thickness Max:4mm; Range:10mm - 20mm; Range:10mm - 20mm; Shank Dia:9mm; ;RoHS Compliant: NA |
發布緊急采購，3分鐘左右您將得到回復。