- 您現在的位置：買賣IC網 > PDF目錄382300 > MC2GH256NMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC2GH256NMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 87/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC2GH256NMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁當前第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
87
Sep.22.2005
Revision 0.3
7.13 Error Conditions
7.13.1
CRC and Illegal Command
All commands are (optionally) protected by CRC (cyclic redundancy check) bits. If the addressed MultiMediaCard's CRC
check fails, the COM_CRC_ERROR bit will be set in the card's response. Similarly, if an illegal command has been
received the ILLEGAL_COMMAND bit will be set in the card's response.
There are different kinds of illegal commands:
Commands which belong to classes not supported by the MultiMediaCard (e.g. interrupt and I/O commands).
Commands not allowed in SPI mode (e.g. CMD20 - write stream)
Commands which are not defined (e.g. CMD47).
7.13.2
Read, Write, Erase And Force Erase Time-out Conditions
The time period after which a time-out condition for read/write/erase operations occurs are (card independent) 10 times
longer than the typical access/program times for these operations given below. A card shall complete the command within
this time period, or give up and return an error message. If the host does not get a response within the defined time-out it
should assume the card is not going to respond any more and try to recover (e.g. reset the card, power cycle, reject, etc.).
The typical access and program times are defined as follows:
7.13.3
Read
The read access time is defined as the sum of the two times given by the CSD parameters TAAC and NSAC. These card
parameters define the typical delay between the end bit of the read command and the start bit of the data block. This num-
ber is card dependent.
7.13.4
Write
The R2W_FACTOR field in the CSD is used to calculate the typical block program time obtained by multiplying the read
access time by this factor. It applies to all write/erase commands (e.g. SET(CLEAR)_WRITE_PROTECT,
PROGRAM_CSD(CID) and the block write commands).
7.13.5
Erase
The duration of an erase command will be (order of magnitude) the number of write blocks to be erased multiplied by the
block write delay.
7.13.6
Force Erase
The Force Erase time-out is specified in Chapter 6.5.2
相關PDF資料 |
PDF描述 |
|---|---|
| MC2GH512DMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH01GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC2GH512DMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GU01GNMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2GU512NMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2M | 制造商:G & J HALL 功能描述:STEP DRILL 10-20MM 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP; Drill Bit Size Metric:10mm; Overall Length:77.5mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Material:Steel; Material Thickness Max:4mm; Range:10mm - 20mm; Range:10mm - 20mm; Shank Dia:9mm; ;RoHS Compliant: NA |
發布緊急采購，3分鐘左右您將得到回復。