- 您現在的位置：買賣IC網 > PDF目錄382300 > MC2GH256NMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC2GH256NMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 92/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC2GH256NMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁當前第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
92
Sep.22.2005
Revision 0.3
1) The default block length is as specified in the CSD.
2) The data transferred must not cross a physical block boundary unless READ_BLK_MISALIGN is set in the CSD.
3) The data transferred must not cross a physical block boundary unless WRITE_BLK_MISALIGN is set in the CSD.
4) R1b : R1 is response with an optional trailing busy signal.
5) 32 write protection bits (representing 32 write protect groups starting at the specified address) followed by 16 CRC bits
are transferred in a payload format via the data line. The last (least significant) bit of the protection bits corresponds to the
first addressed group. If the address of the last groups are outside the valid range, then the corresponding write protection
bits are set to zero.
6) RD/WR_: "1" the host receives a data block from the card.
"0" the host sends a data block to the card.
7.18 Responses
There are several types of response tokens. As in the MultiMediaCard mode, all are transmitted MSB first:
7.18.1
Format R1
This response token is sent by the card after every command, with the exception of SEND_STATUS commands. It is one
byte long, and the MSB is always set to zero. The other bits are error indications, an error being signaled by a ‘1’. The
structure of the R1 format is given in Figure 7-8. The meaning of the flags is defined as follows:
In idle state
: The card is in idle state and running the initializing process.
Erase Reset:
An erase sequence was cleared before executing because ‘non erase’ command (neither of CMD35,
CMD36, CMD38 or CMD13) was received.
Illegal Command
: An illegal command code was detected or the card did not switch to the requested mode.
Communication CRC Error
: The CRC check of the last command failed.
Erase Sequence Error
: An error occurred in the sequence of erase commands (CMD35, CMD36, CMD38).
Address Misaligned
: A misaligned block is detected during data transfer.
Address Out Of Range | Block Length Error
: The command’s argument was out of the allowed range for this card.
CMD
INDEX
SPI
Mode
Argument
Resp
Abbreviation
Command Description
CMD43
...
CMD54
reserved
CMD55
Yes
[31:0] stuff bits
R1
APP_CMD
Defines to the card that the next command
is an application specific command rather
than a standard command
CMD56
Yes
[31:1] stuff bits
[0] RD/WR_
6
R1b
GEN_CMD
Used either to transfer a data block to the
card or to get a data block from the card
for general purpose / application sepcific
commands. The size of the data block is
defined by the SET_BLOCK_LEN com-
mand.
CMD57
Reserved
CMD58
Yes
None
R3
READ_OCR
Reads the OCR register of a card
CMD59
Yes
[31:1] stuff bits
[0:0] CRC option
R1
CRC_ON_OFF
Turns the CRC option on or off. A ‘1’ in the
CRC option bit will turn the option on, a ‘0’
will turn it off
CMD60
...
CMD63
No
相關PDF資料 |
PDF描述 |
|---|---|
| MC2GH512DMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH01GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC2GH512DMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GH512NMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GU01GNMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2GU512NMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2M | 制造商:G & J HALL 功能描述:STEP DRILL 10-20MM 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP; Drill Bit Size Metric:10mm; Overall Length:77.5mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Material:Steel; Material Thickness Max:4mm; Range:10mm - 20mm; Range:10mm - 20mm; Shank Dia:9mm; ;RoHS Compliant: NA |
發布緊急采購，3分鐘左右您將得到回復。