- 您現在的位置：買賣IC網 > PDF目錄382300 > MC2GH512DMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC2GH512DMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 41/102頁 |
| 文件大?。?/td> | 1384K |
| 代理商： | MC2GH512DMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
41
Sep.22.2005
Revision 0.3
The command CMD1 shall be implemented by all cards defined by this standard.
If the host intends to operate the Dual Voltage MultiMediaCards in the 1.65V to 1.95V range, it is recommended that the
host first validate the operating voltage in the 2.7V to 3.6V range, then power the card down fully, and finally power the
card back up to the 1.65V to 1.95V range for operation. Using the 2.7V to 3.6V range initially, which is common to High
and Dual voltage MultiMediaCards, will allow reliable screening of host & card voltage incompatibilities. High voltage cards
may not function properly if VDD < 2.0V is used to establish communication. Dual voltage cards may fail if 1.95 to 2.7V is
used.
6.1.3 Card Identification Process
The following explanation refers to a card working in a multi-card environment, as defined in versions of this standard pre-
vious to v4.0, and it is maintained for backwards compatibility to those systems.
The host starts the card identification process in open-drain mode with the identification clock rate f
OD
(see Chapter 5.4.8).
The open drain driver stages on the CMD line allow parallel card operation during card identification.
After the bus is activated, the host will request the cards to send its valid operation conditions (CMD1). The response to
CMD1 is the ‘wired and’ operation on the condition restrictions of all cards in the system. Incompatible cards are sent into
Inactive State
. The host then issues the broadcast command ALL_SEND_CID (CMD2), asking all cards for its unique card
identification (CID) number. All unidentified cards (i.e. those which are in
Ready State
) simultaneously start sending their
CID numbers serially, while bit-wise monitoring their outgoing bitstream. Those cards, whose outgoing CID bits do not
match the corresponding bits on the command line in any one of the bit periods, stop sending their CID immediately and
must wait for the next identification cycle (remaining in the
Ready State
). Since CID numbers are unique for each card,
there should be only one card which successfully sends its full CID-number to the host. This card then goes into
Identifica-
tion State
. Thereafter, the host issues CMD3 (SET_RELATIVE_ADDR) to assign to this card a relative card address
(RCA), which is shorter than CID and which will be used to address the card in the future data transfer mode (typically with
a higher clock rate than f
OD
). Once the RCA is received the card state changes to the
Stand-by State,
and the card does
not react to further identification cycles. Furthermore, the card switches its output drivers from open-drain to push-pull.
The host repeats the identification process, i.e. the cycles with CMD2 and CMD3 as long as it receives a response (CID)
to its identification command (CMD2). If no more card responds to this command, all cards have been identified. The time-
out condition to recognize completion of the identification process is the absence of a start bit for more than
N
ID
clock
cycles after sending CMD2 (see timing values in Chapter 6.11).
相關PDF資料 |
PDF描述 |
|---|---|
| MC2GH512NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH01GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC2GH512NMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GU01GNMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2GU512NMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2M | 制造商:G & J HALL 功能描述:STEP DRILL 10-20MM 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP; Drill Bit Size Metric:10mm; Overall Length:77.5mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Material:Steel; Material Thickness Max:4mm; Range:10mm - 20mm; Range:10mm - 20mm; Shank Dia:9mm; ;RoHS Compliant: NA |
| MC2N2906A | 制造商:SPC Multicomp 功能描述:BIPOLAR TRANSISTOR, PNP, -60V TO-18; Transistor Polarity:PNP; Collector Emitter Voltage V(br)ceo:-60V; Transition Frequency Typ ft:200MHz; Power Dissipation Pd:400mW; DC Collector Current:-600mA; DC Current Gain hFE:40; No. of Pins:3;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。