- 您現在的位置：買賣IC網 > PDF目錄382300 > MC2GH512DMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC2GH512DMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 47/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC2GH512DMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
47
Sep.22.2005
Revision 0.3
Block Read
Block read is similar to stream read, except the basic unit of data transfer is a block whose maximum size is defined in the
CSD (READ_BL_LEN). If READ_BL_PARTIAL is set, smaller blocks whose starting and ending address are entirely con-
tained within one physical block (as defined by READ_BL_LEN) may also be transmitted. Unlike stream read, a CRC is
appended to the end of each block ensuring data transfer integrity. CMD17 (READ_SINGLE_BLOCK) initiates a block
read and after completing the transfer, the card returns to the
Transfer State
.
CMD18 (READ_MULTIPLE_BLOCK) starts a transfer of several consecutive blocks. Two types of multiple block read
transactions are defined (the host can use either one at any time):
Open-ended Multiple block read
The number of blocks for the read multiple block operation is not defined. The card will continuously transfer data
blocks until a stop transmission command is received.
Multiple block read with pre-defined block count
The card will transfer the requested number of data blocks, terminate the transaction and return to
transfer
state. Stop
command is not required at the end of this type of multiple block read, unless terminated with an error. In order to start
a multiple block read with pre-defined block count the host must use the SET_BLOCK_COUNT command (CMD23)
immediately preceding the READ_MULTIPLE_BLOCK (CMD18) command. Otherwise the card will start an open
-ended multiple block read which can be stopped using the STOP_TRANSMISION command.
The host can abort reading at any time, within a multiple block operation, regardless of the its type. Transaction abort is
done by sending the stop transmission command.
If either one of the following conditions occur, the card will reject the command, remain in
Tran
state and respond with the
respective error bit set.
The host provides an out of range address as an argument to either CMD17 or CMD18.
ADDRESS_OUT_OF_RANGE is set.
The currently defined block length is illegal for a read operation. BLOCK_LEN_ERROR is set.
The address/block-length combination positions the first data block misaligned to the card physical blocks.
ADDRESS_MISALIGN is set.
If the card detects an error (e.g. out of range, address misalignment, internal error, etc.) during a multiple block read oper-
ation (both types) it will stop data transmission and remain in the
Data State.
The host must then abort the operation by
sending the stop transmission command. The read error is reported in the response to the stop transmission command.
If the host sends a stop transmission command after the card transmits the last block of a multiple block operation with a
pre-defined number of blocks, it is regarded as an illegal command, since the card is no longer in
data
state.
If the host uses partial blocks whose accumulated length is not block aligned, and block misalignment is not allowed, the
card shall detect a block misalignment error condition during the transmission of the first misaligned block and the content
of the further transferred bits is undefined. As the host sends CMD12 the card will respond with the ADDRESS_MISALIGN
bit set and return to
Tran
state.
If the host sets the argument of the SET_BLOCK_COUNT command (CMD23) to all 0s, then the command is accepted;
however, a subsequent read will follow the open-ended multiple block read protocol (STOP_TRANSMISSION command -
CMD12 - is required).
相關PDF資料 |
PDF描述 |
|---|---|
| MC2GH512NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH01GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC2GH512NMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GU01GNMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2GU512NMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2M | 制造商:G & J HALL 功能描述:STEP DRILL 10-20MM 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP; Drill Bit Size Metric:10mm; Overall Length:77.5mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Material:Steel; Material Thickness Max:4mm; Range:10mm - 20mm; Range:10mm - 20mm; Shank Dia:9mm; ;RoHS Compliant: NA |
| MC2N2906A | 制造商:SPC Multicomp 功能描述:BIPOLAR TRANSISTOR, PNP, -60V TO-18; Transistor Polarity:PNP; Collector Emitter Voltage V(br)ceo:-60V; Transition Frequency Typ ft:200MHz; Power Dissipation Pd:400mW; DC Collector Current:-600mA; DC Current Gain hFE:40; No. of Pins:3;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。