- 您現在的位置：買賣IC網 > PDF目錄382300 > MC2GH512DMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC2GH512DMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 42/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC2GH512DMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
42
Sep.22.2005
Revision 0.3
6.2 Data Transfer Mode
When the card is in
Stand-by State,
communication over the CMD and DAT lines will be performed in push-pull mode.
Until the contents of the CSD register is known by the host, the f
PP
clock rate must remain at f
OD
(see Chapter 5.4.8). The
host issues SEND_CSD (CMD9) to obtain the Card Specific Data (CSD register), e.g. block length, card storage capacity,
maximum clock rate, etc.
Figure 6-2 : MultiMediaCard State Diagram (Data Transfer Mode)
The broadcast command SET_DSR (CMD4) configures the driver stages of the card. It programs its DSR register corre-
sponding to the application bus layout (length) and the data transfer frequency. The clock rate is also switched from f
OD
to
f
PP
at that point.
CMD7 is used to select the card and put it into the
Transfer State
. If the card was previously selected and was in
Transfer
State
its connection with the host is released and it will move back to the
Stand-by State
. When CMD7 is issued with the
reserved relative card address “0x0000”, the card is put back to
Stand-by State
. After the card is assigned an RCA it will
not respond to identification commands (CMD1, CMD2, CMD3, see Chapter 6.1.3).
State (tran)
Stand-by State
(stby)
Transfer
Sending-data
State (data)
CMD3
CMD4
9,10,39
CMD7
CMD16,
23,35,36
CMD7
CMD8,11,17,
18, 30, 56(r)
Data transfer
mode
Card identification
mode
CMD13 & CMD55
in data-transfer-mode
no state transition
CMD12,
“operation
complete”
State (rcv)
Receive-data
24,25,26,27,42, 56(w)
CMD20,
CMD15
from all states in
Data-transfer-mode
State (prg)
Programming
28, 29, 38
CMD 6,
“operation
complete”
State (dis)
Disconnect
CMD7
“operation
complete”
CMD0
CMD7
CMD24,
25
CMD12 or
transfer end“
CMD40
Wait-IRQ State
(irq)
Any start bit
detected on
the bus
Interrupt mode
CMD19
Bus test
State (btst)
CMD14
相關PDF資料 |
PDF描述 |
|---|---|
| MC2GH512NMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH01GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC2GH512NMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC2GU01GNMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2GU512NMCA-0QC00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:MultiMediaCard Specification |
| MC2M | 制造商:G & J HALL 功能描述:STEP DRILL 10-20MM 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP 制造商:G & J HALL 功能描述:STEP DRILL, 10-20MM, 1MM STEP; Drill Bit Size Metric:10mm; Overall Length:77.5mm; SVHC:No SVHC (19-Dec-2012); Drill Bit Type:Step; Material:Steel; Material Thickness Max:4mm; Range:10mm - 20mm; Range:10mm - 20mm; Shank Dia:9mm; ;RoHS Compliant: NA |
| MC2N2906A | 制造商:SPC Multicomp 功能描述:BIPOLAR TRANSISTOR, PNP, -60V TO-18; Transistor Polarity:PNP; Collector Emitter Voltage V(br)ceo:-60V; Transition Frequency Typ ft:200MHz; Power Dissipation Pd:400mW; DC Collector Current:-600mA; DC Current Gain hFE:40; No. of Pins:3;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。