- 您現在的位置：買賣IC網 > PDF目錄371053 > MC68HC901FN (MOTOROLA INC) Multi-Function Peripheral PDF資料下載
參數資料
| 型號： | MC68HC901FN |
| 廠商： | MOTOROLA INC |
| 元件分類： | 外設及接口 |
| 英文描述： | Multi-Function Peripheral |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQCC52 |
| 封裝： | PLASTIC, LCC-52 |
| 文件頁數： | 15/73頁 |
| 文件大小： | 274K |
| 代理商： | MC68HC901FN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
Signal Description
2-2
MC68HC901 USER’S MANUAL
MOTOROLA
2.2 CLOCK (CLK)
The clock input is a single-phase TTL-compatible signal used for internal timing. This input
must conform to minimum pulse width times. The clock is not necessarily the system clock
in frequency or phase.
2.3 DATA BUS (D7–D0)
This three-state bidirectional bus is used to transmit data to or receive data from the MFP
internal registers during a processor read or write cycle, respectively. During an interrupt
acknowledge cycle, the data bus is used to pass a vector number to the processor. The MFP
must be located on data bus lines D7–D0 when used with either the MC68000 series of
microprocessors and on data lines D31–D24 when used with the MC68020 microprocessor,
if vectored interrupts are to be used.
2.4 ASYNCHRONOUS BUS CONTROL
Asynchronous data transfers are controlled by chip select, data strobe, read/write, and data
transfer acknowledge. The register select lines, RS5–RS1, select an internal MFP register
for a read or write operation. The reset line initializes the MFP registers and the internal
control signals.
2.4.1 Chip Select (CS)
This active low input activates the MFP for internal register access. CS and IACK must not
be asserted at the same time.
2.4.2 Data Strobe (DS)
This active low input is part of the internal chip select and interrupt acknowledge functions.
2.4.3 Read/Write (R/W)
This input defines the current bus cycle as a read (high) or a write (low) cycle.
2.4.4 Data Transfer Acknowledge (DTACK)
This active low, three-state output signals the completion of the operation phase of a bus
cycle to the processor. If the bus cycle is a process read, the MFP asserts DTACK to indicate
that the information on the data bus is valid. If the bus cycle is a processor write to the MFP,
DTACK acknowledges the acceptance of the data by the MFP. DTACK will be asserted only
by a MFP that has CS or IACK (and IEI) asserted.
2.5 REGISTER SELECT BUS (RS1–RS5)
The register select bus selects an internal MFP register during a read or write operation.
2.6 RESET (RESET)
This active low input will initialize the MFP during powerup or in response to a total system
reset. Refer to
Section 3.3 Reset Operation
for further information.
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC901P | Multi-Function Peripheral |
| MC68HC916X1 | 16-Bit Modular Microcontroller(16位模塊化微控制器) |
| MC68HC9D60 | Advance Information - Rev 4.0 |
| MC68HC12D60 | Advance Information - Rev 4.0 |
| MC68HCL05C8A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC908AB32CFU | 功能描述:IC MCU 8MHZ 32K FLASH 64-QFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC08 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| MC68HC908AB32MFU | 制造商:Rochester Electronics LLC 功能描述:32K FLASH & 512 EE - Bulk |
| MC68HC908AB32MPB | 功能描述:IC MCU 32K FLASH 8MHZ 64-LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC08 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HC908AP16CB | 功能描述:IC MCU 16K FLASH 8MHZ 42SDIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC08 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HC908AP16CBE | 制造商:Freescale Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。