- 您現在的位置：買賣IC網 > PDF目錄371053 > MC68HC901FN (MOTOROLA INC) Multi-Function Peripheral PDF資料下載
參數資料
| 型號： | MC68HC901FN |
| 廠商： | MOTOROLA INC |
| 元件分類： | 外設及接口 |
| 英文描述： | Multi-Function Peripheral |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQCC52 |
| 封裝： | PLASTIC, LCC-52 |
| 文件頁數： | 16/73頁 |
| 文件大小： | 274K |
| 代理商： | MC68HC901FN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
Signal Description
MOTOROLA
MC68HC901 USER’S MANUAL
2-3
2.7 INTERRUPT CONTROL
The interrupt request and interrupt acknowledge signals are handshake lines for a vectored
interrupt scheme. Interrupt enable in and interrupt enable out implement a daisy-chained
interrupt structure.
2.7.1 Interrupt Request (IRQ)
This active low, open-drain output signals to the processor that an interrupt is pending from
the MFP. There are 16 interrupt channels that can generate an interrupt request. Clearing
the interrupt pending registers (IPRA and IPRB) or clearing the interrupt mask registers
(IMRA and IMRB) will cause the IRQ to be negated. IRQ will also be negated as the result
of an interrupt acknowledge cycle, unless additional interrupts are pending in the MFP.
Refer to
Section 4 Interrupt Structure
for further information.
2.7.2 Interrupt Acknowledge (IACK)
If both IRQ and IEI are asserted, the MFP will begin an interrupt acknowledge cycle when
IACK and DS are asserted. The MFP will supply a unique vector number to the processor
which corresponds to the particular channel requesting interrupt service. In a daisy-chained
interrupt structure, all devices in the chain must have a common IACK. Refer to
Interrupt Acknowledge Operation
and
Section 4.1.2 Interrupt Vector Number
additional information. CS and IACK must not be asserted at the same time.
Section 3.2
for
2.7.3 Interrupt Enable In (IEI)
This active low input, together with the IEO signal, provides a daisy-chained interrupt
structure for a vectored interrupt scheme. IEI indicates that no higher priority device is
requesting interrupt service. So, the highest priority MFP in the chain should have its IEI pin
tied low. During an interrupt acknowledge cycle, a MFP with a pending interrupt is not
allowed to pass a vector number to the processor until its IEI pin is asserted. When the
daisy-chain option is not implemented, all MFPs should have their IEI pin tied low. Refer to
Section 4.2 Daisy-Chaining MFPs
for additional information.
2.7.4 Interrupt Enable Out (IEO)
This active low output, together with the IEI signal, provides a daisy-chained interrupt
structure for a vectored interrupt scheme. The IEO of a particular MFP signals lower priority
devices that neither it nor any other higher priority device is requesting interrupt service.
When a daisy-chain is implemented, IEO is tied to the next lower priority MFP IEI input. The
lowest priority MFP is not connected. When the daisy-chain option is not implemented, IEO
is not connected. Refer to
Section 4.2 Daisy-Chaining MFPs
for additional information.
2.8 GENERAL PURPOSE I/O INTERRUPT LINES (I7–I0)
These lines constitute an 8-bit pin-programmable I/O port with interrupt capability. The data
direction register (DDR) individually defines each line as either a high-impedance input or a
TTL-compatible output. As an input, each line can generate an interrupt on the user selected
transition of the input signal. Refer to
Section 5 General Purpose Input/Output Port
further information.
for
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC901P | Multi-Function Peripheral |
| MC68HC916X1 | 16-Bit Modular Microcontroller(16位模塊化微控制器) |
| MC68HC9D60 | Advance Information - Rev 4.0 |
| MC68HC12D60 | Advance Information - Rev 4.0 |
| MC68HCL05C8A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC908AB32CFU | 功能描述:IC MCU 8MHZ 32K FLASH 64-QFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC08 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| MC68HC908AB32MFU | 制造商:Rochester Electronics LLC 功能描述:32K FLASH & 512 EE - Bulk |
| MC68HC908AB32MPB | 功能描述:IC MCU 32K FLASH 8MHZ 64-LQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC08 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HC908AP16CB | 功能描述:IC MCU 16K FLASH 8MHZ 42SDIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC08 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC68HC908AP16CBE | 制造商:Freescale Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。